Ford Vedette nameplate
€10.80 TTC
(10,80 € HT)
(10,80 € HT)
2-pin push button - 60 Amp - metal body - starter control
€9.60 TTC
(8,00 € HT)
(8,00 € HT)
Rear window seal Ford Vedette Coupe
Rear window seal, welded, for Coupé Vedette.
€137.16 TTC
(114,30 € HT)
(114,30 € HT)
Windscreen seal Ford Vedette 1949/52 - with central pillar
Welded windscreen seal - with central upright - for Vedette 1949 to 52. Photo no contractual
€204.00 TTC
(170,00 € HT)
(170,00 € HT)
Gray needle button for Ford Vedette 53 and 54 dashboard
Resin button with Ford Vedette gray lacquered needle, with thread insert, as original.Sold individually. Please note this model with anti-rotation needle screw is intended for Fog and Heating controls (1953 to 54)
€20.92 TTC
(20,92 € HT)
(20,92 € HT)
Soles kit for handles and locks - Ford Vedette coupe / cabriolet
Soles kit for Ford Vedette coupe and convertible. French manufacture by Techni-Tacot.Including:2 x soft soles for exterior door handles2 x soft soles for exterior door lock
€25.20 TTC
(25,20 € HT)
(25,20 € HT)
Kit of 2 x wiper soles - Ford Vedette from 1949 to 1952
Sole kit for Ford Vedette from 1949 to 1952. Made in France by Techni-Tacot.Including:2 x wiper soles.
€11.90 TTC
(11,90 € HT)
(11,90 € HT)
Gray gear lever knob for Ford Vedette dashboard
Gear shift knob, in Ford Vedette gray lacquered resin, with thread insert, as original
€40.60 TTC
(40,60 € HT)
(40,60 € HT)
Boot handle sole kit - Ford Vedette 1949 -53 - sedan / coupe / cabriolet
Sole for Ford Vedette sedan, coupe, convertible. French manufacture by Techni-Tacot.Including:1 x sole for the trunk handle.
€26.68 TTC
(26,68 € HT)
(26,68 € HT)
Clip-on exterior mirror - parabolic mirror
Clip-on mirror for mounting on door pillar. Supplied with 2 tightening screws + key. Parabolic mirror allowing a greater viewing angle than a flat mirror
€43.20 TTC
(36,00 € HT)
(36,00 € HT)
bras x 2 inox fil axe 5 mm
Bras d'essuie glace inox. tige filaire - Serrage sur axe 5 mm. Se monte avec balais type raclette ou lame - Vendu par 2
€57.60 TTC
(48,00 € HT)
(48,00 € HT)
Circle Steering Wheel for Ford Vedette
Circle Steering Wheel for Ford Vedette,
€640.00 TTC
(640,00 € HT)
(640,00 € HT)
Wiper sole kit - Ford Vedette 1954
Kit semelle pour essuie glace Ford Vedette 1954 - Fabrication française soignée - Exclusivité techni-Tacot Comprend : 2 x semelles essuie glace
€11.90 TTC
(11,90 € HT)
(11,90 € HT)
Windshield wiper - Stainless steel squeegee blades 230 mm x 2- version 2
Stainless steel wiper blades, 23 cm squeegee type. Sold by 2 squeegees
€19.20 TTC
(16,00 € HT)
(16,00 € HT)
Kit of 2 x platinum rear light bases - Ford Vedette from 1949 to 1952
Sole kit for Ford Vedette from 1949 to 1952. Made in France by Techni-Tacot.Including:2 x soles for rear light plate.
€35.50 TTC
(35,50 € HT)
(35,50 € HT)
Viewed products
Fuel pump - GUIOT diaphragm kit Ø90mm - Ford Vedette Simca
Replacement diaphragm for GUIOT fuel pump (Vedette Ford and Simca engine). Diam 90mm. Supplied with membrane and gaskets. (check the type of pump before ordering)
€30.00 TTC
(25,00 € HT)
(25,00 € HT)
Oil seal rings gearbox lever - Simca Versailles Chambord
Set of 2 sealing rings (oil seal) for gearbox controls (mounted on control cover).Gaskets to be glued to immobilize them.
€14.40 TTC
(12,00 € HT)
(12,00 € HT)
Front lights kit 2 x soles - Ford Vedette - 1949 to1952
Sole kit for Ford Vedette - 1949 to 1952. French manufacture by Techni-Tacot.Including:2 x soles for front light plate.
€35.70 TTC
(35,70 € HT)
(35,70 € HT)
Calibrouge (Plastigage) mechanical clearance measurement
"Plastigage"The Calibrouge ("plastigage or plastigauge") is a simple and practical tool for measuring the clearances of your bearings. Range of use: operating clearance from 0.025 to 0.175 mm
€27.00 TTC
(22,50 € HT)
(22,50 € HT)
Base gasket x4 - Ø 93 ep 1.05 mm- Renault Fregate etc.
Set of 4 base gaskets (sleeve Ø 93 mm) all copper thickness 1.05 mm (approximately) for Renault type 671 engine (Colorale, Goélette, R2087, Frégate, etc.)
€54.00 TTC
(45,00 € HT)
(45,00 € HT)
Valve guides x 4 ADM ECH - 9x61x 15.14 ORIGIN - Renault Fregate - Prairie - Goelette - R2087 - SG2
Set of 4 valve guides (cast iron) dimensions approx. 61 x Ø 15.14 - Ø int 9 mm - ADM and ECH - Fitting on gasoline engine 668 - 671 - 817 Renault. Suitable for cylinder heads fitted with 2 rocker arms separated by the central greasing tee.French ...
€90.00 TTC
(75,00 € HT)
(75,00 € HT)
Rod bearings Renault Goelette Frégate dimension 0.25 - 54.75 mm
Set of 8 connecting rod bearings dimension 0.25 crankpin d 54.75 mm - Renault, Colorale, Goélette, R2087, Frégate, Sg2, etc).668 and 671 engine and super standard 817 - 2.6 L
€321.00 TTC
(267,50 € HT)
(267,50 € HT)
