12V electric fuel pump

" 12V electric fuel pump. Connects in series with the original fuel line. Keeps the hand pump. Avoids having to lift the hood to turn up gasoline before starting. To be powered through a push button for occasional operation. Low pressure, no need ...

12v to 6v regulator for temperature, pressure, fuel gauge

This module allows the use of 6V pressure gauges on a 12V vehicle (negative to ground). Mounts on a temperature gauge, pressure, fuel gauge, ...Very practical, it is fixed directly on the supply terminal of the pressure gauge thanks to a hole ...

50 mm galvanized flange or collar exhaust - Simca Versailles Chambord

Flange for exhaust connection (clamp with caliper)

6V electric fuel pump

6V electric fuel pump. To be connected to the ignition coil power supply. Connects in series with the original fuel line.Allows you to keep the manual pump. Avoids having to lift the hood to turn up gasoline before starting.Is intended to remain ...

ADM Simca Versailles - Chambord valve

Intake valve for Simca Trianon, Versailles, Régence, Beaulieu, Chambord, Présidence, Marly 1 and 2, Ariane 8.Product from old stocks or used product reconditioned - Delivered rectified and ready to fit.

Aerosol gasket for cylinder head

Sealing spray varnish to be sprayed on both sides of a cylinder head gasket. Improves sealing, essential with solid copper gaskets (any thickness)

Aviation collex type paste gasket for cylinder head - 450ml

Sealing paste to be applied on both sides of a cylinder head gasket. Product similar to "Collex". Leave to evaporate for about 30 min at room temperature after application, then fit the gasket - improves the seal - recommended with solid copper ...

Battery switch - safety

Battery isolator - used to electrically isolate the battery. To be placed on a terminal of the battery.

Battery switch with key - security

Battery switch with key - security

bearing 35 72 17 groove gearbox simca v8

Bearing 35x72x17 with locking groove, special Simca Versailles Chambord gearbox and derivatives

Bearing 6203 - 17x40x12

Bearing - 17x40x12 waterproof (often used on dynamo, water pump, flywheel center, etc.). Check with the dimensions of your bearing.

Bearings - set of 2 side shims - Simca Versailles Chambord STD

Set of 2 crankshaft shims Simca Versailles, Chambord, Ariane 8 etc. "Aquilon" V8 engine.You need 2 sets per motor

Bearings for Simca Versailles Chambord 010 - 53.04 mm

" Set of bearings for Simca Versailles, Chambord, Ariane 8 etc. V8 engine" "Aquilon" ". (1 rear landing + 2 front and central single landings) Dimension: .010 US (0.25 mm) "

Bearings for Simca Versailles Chambord 020 - 52.79 mm

Set of bearings for Simca Versailles, Chambord, Ariane 8 etc. V8 "Aquilon" engine.(1 rear bearing + 2 front and central single bearings)Dimension: 020 US (0.50 mm)

Bearings for Simca Versailles Chambord 030 - 52.53 mm

" Set of bearings for Simca Versailles, Chambord, Ariane 8 etc. V8 engine" "Aquilon" ". (1 rear landing + 2 front and central single landings) Dimension: 030 US (0.75 mm) "

Bearings for Simca Versailles Chambord standard - 53.30 mm

Set of bearings for Simca Versailles, Chambord, Ariane 8 etc. V8 "Aquilon" engine. (1 rear bearing + 2 front and central single bearings) Dimension: STD

Calibrouge (Plastigage) mechanical clearance measurement

"Plastigage"The Calibrouge ("plastigage or plastigauge") is a simple and practical tool for measuring the clearances of your bearings. Range of use: operating clearance from 0.025 to 0.175 mm

Central intake gasket Ford Vedette Simca

Central gasket intake housing for Vedette Ford and Simca.

CHAMBORD exhaust - n2 - stainless steel primary tube - Simca Chambord

Primary tube between the "Y" and the silencer - Part 2 on the photoAll stainless steel.

€109.98 TTC
(91,65 € HT)

CHAMBORD exhaust - oval stainless steel silencer (n ° 3) - Simca Chambord

Stainless steel silencer exhaust for V8 Simca Aquilon

€525.32 TTC
(437,77 € HT)

Charger and maintenance 6v / 12v Accumate

AccuMate is designed to automatically charge and monitor batteries without the danger of overcharging them, regardless of plug-in time. AccuMate is available for all 6V and 12V lead acid batteries, making it a perfect accessory for owners of ...

copy of Oil pressure contact mano - Ford Vedette 1949 - 54

oil pressure switch for Ford Vedette engine from 1949 to 1954 - Thread M 10x100

copy of Segment set Ø 66.80 mm Simca Chambord 2.38x2.38x5 - 8cyl

Segment set Ø 66.80 mm Simca 2.38x2.38x5 - 8cyl

Cross shaft transmission Simca Versailles Chambord

Transmission shaft crosspiece Simca Trianon, Versailles, Marly, Beaulieu, Chambord, Presidence.23.8 mm x 61.3 mm - assembly with external circlips (supplied with each spider). Check your dimensions precisely because other models have been fitted. ...

Dark green engine paint RAL 6005 - 500 ml

Dark green engine paint RAL 6005 -Pot of 500 mlSuitable for engines, housings, gearboxes, differentials, brake drums and all parts subject to heating in cast iron, steel and light alloys.Direct application on degreased metal (or better, treated ...

€40.80 TTC
(34,00 € HT)

Disc set of 2 - upper block approx Ø 25 mm Simca

Set of 2 tablets for Simca engine block. Mounting on the surface plane: approximately 25.9 mm. Simca Trianon, Versailles, Régence, Beaulieu, Chambord, Présidence, Marly 1 et2, Ariane 8

Double pressure gauge holder

Metal support, black lacquered for standard manometer D52 mm. Ready to fix.

Dynamo belt for Simca Versailles Chambord

Dynamo-water pump-crankshaft pulley belt.

ECH valve Simca Versailles - Chambord

Exhaust valve for Simca Trianon, Versailles, Régence, Beaulieu, Chambord, Présidence, Marly 1 and 2, Ariane 8.Product from old stocks or reconditioned used product. - Delivered rectified and ready to fit.

Echappement joint extremite bloc V8 Ford Vedette et Simca

" Exhaust gasket, engine block outlet, small model placed at the ends. 4 on one engine - Sold individually. "

Echappement sangle support renforcé 50 mm

Sangle de suspension pour échappement, caoutchouc armé. entraxe 52 mm pour vis M8 mm.

Electronic ignition amplifier assistance module - 12V negative to earth

Electronic ignition assistance module. Allows for more energetic spark plug ignition, improved starting, smoother pick-up, helps reduce fuel consumption and consequently pollution.The breakers (platinum-plated screws) are left in place - the ...

Engine paint black RAL 9005 - 500 ml

Black paint - 500 ml jarSuitable for engines, housings, gearboxes, differentials, brake drums and all parts subject to heating in cast iron, steel and light alloys.Direct application on degreased metal (or better, treated with our Phosprim 4090), ...

€40.80 TTC
(34,00 € HT)

Engine paint oxide green RAL 6020 - 500 ml

Engine paint oxide green RAL 6020 -Pot of 500 mlSuitable for engines, housings, gearboxes, differentials, brake drums and all parts subject to heating in cast iron, steel and light alloys.Direct application on degreased metal (or better, treated ...

€40.80 TTC
(34,00 € HT)

Engine red paint - 500 ml -

Engine red paint -Pot of 500 mlSuitable for engines, housings, gearboxes, differentials, brake drums and all parts subject to heating in cast iron, steel and light alloys.Direct application on degreased metal (or better, treated with our Phosprim ...

€40.80 TTC
(34,00 € HT)

exhaust - stainless steel Y tube (n ° 1) - Simca Chambord

" Stainless steel exhaust - Y connecting the 2 cast iron manifolds to the line. Part n ° 1 on the photo "

Exhaust - tube + stainless steel final stock (n ° 4) - Simca Chambord

" Outlet tube with bracket (passage of the bridge) to be connected to the outlet of the silencer. All stainless steel. "

Exhaust gasket center block V8 Ford Vedette and Simca

Exhaust gasket, engine block outlet (center). 2 per engine - Sold individually.

Exhaust gasket outlet manifold V8 Ford Vedette and Simca

" Exhaust gasket - at the manifold outlet - connection with" "Y" "2 in 1. 2 per engine - Sold individually. "

Exhaust kit 8 seals Ford Vedette and Simca Versailles Chambord

" Assortment of 8 exhaust gaskets for an engine. Either: 2 central manifold joints on block 4 manifold outer joints on block 2 manifold outlet seals to 2 in 1 tube. "

Exhaust manifold paint - 250 ml

€48.00 TTC
(40,00 € HT)

Exhaust Presidence - n1 - stainless steel Y tube - Simca Presidence

Stainless steel exhaust - Y - connecting the 2 cast iron manifolds to the line.Part n ° 1 on the photo

€415.34 TTC
(346,12 € HT)

Exhaust Presidence - n2 - stainless steel primary tube - Simca Presidence

Primary tube between the "Y" and the silencer - Part 2 on the photoAll stainless steel.

€109.98 TTC
(91,65 € HT)

Exhaust Presidence - n3 - oval stainless steel silencer - Simca Presidence

Stainless steel silencer exhaust for V8 Simca Aquilon

€552.24 TTC
(460,20 € HT)

Exhaust Presidence - n4 - stainless steel rear double outlet tube - Simca Presidence

Outlet tube with crossbar (passage of the bridge) with double outlet after silencer.All stainless steel.

€661.04 TTC
(550,87 € HT)

Exhaust silent bloc

Echappement silent bloc support renforcé 26 mm long hors tout 65 mm - filetage M8

Exhaust support strap reinforces 90 mm

Suspension strap for exhaust. Robust construction, reinforced rubber, metal eyelets.92 mm center distance for M8 mm screws.

Exhaust suspension ring 63x96 width 27 mm - Peugeot 203

Suspension ring for Peugeot 203 exhaust and othersDimension approximately 63 x 96 x width 27 mm

Ford and Simca Vedette rod stopper

Set of 16 retainers for V8 Simca or Ford Vedette connecting rod. V8 12 and 13cvOriginally compliant

Ford RAL 5005 blue engine paint - 500 ml

Ford RAL 5005 blue engine paint - 500 ml jarSuitable for engines, housings, gearboxes, differentials, brake drums and all parts subject to heating in cast iron, steel and light alloys.Direct application on degreased metal (or better, treated with ...

€40.80 TTC
(34,00 € HT)

Ford Vedette and Simca Versailles Chambord braid set

" Set of braids for crankshaft Vedette Ford and Simca Aquilon engine (rear bearing and front bearing) Versailles, Chambord etc ... New product, of very high technical quality. Mounts with ease, cuts easily with a cuter leaving 1 to 2 mm ...

Ford Vedette Simca V8 Calorstat Thermostat

" Thermostat for cooling circuit. For V8 Vedette Ford and Simca Versailles, Chambord, Vendôme, Monte Carlo etc. (Two thermostats per V8 engine). Sold individually. "

fuel filter Big size ø 6 and 8 mm

Paper fuel filter for 6 or 8 mm hose.

fuel filter ø 6 and 8 mm

Paper fuel filter for 6 or 8 mm hose.

Fuel gauge - replacement float

Float in synthetic material resistant to current fuels. Used to replace the cork floats on the fuel gauge Length: 1.40" Diameter: 1.14"

Fuel gauge - replacement plastic float

White plastic float. Used to replace ring gauge floats.

Fuel hose diam 8 mm - by the meter

8 mm fuel hose sold by the meter.

Fuel pump - 6V or 12V control push button

6 or 12v 10A push button. Can be used to activate an electric fuel pump for a few seconds, for example.

Fuel pump - GUIOT diaphragm kit Ø90mm - Ford Vedette Simca

Replacement diaphragm for GUIOT fuel pump (Vedette Ford and Simca engine). Diam 90mm. Supplied with membrane and gaskets. (check the type of pump before ordering)

Gasket paste for motor - auto extrudable cartridge 200 ml

Mot. Silicone gasket & self-extruding housing RTV K164     high-quality, heat-resistant silicone     base: modified oxime silicone (acid-free hardening system)

Gasket water pump for Simca Versailles Chambord engine

Water pump seal

Gauge Gasket cork 3 holes

Cork gasket for 3-hole fuel gauge

Gearbox entry seal ring - Simca Versailles Chambord

Sealing ring (oil seal) for gearbox inlet (clutch side).

Gearbox or axle oil SAE 80-140 - IGOL - 1L

Viscosity index 80 - 140API GL-4(Not suitable for Peugeot type screw axles)

Handle fuel pump - Simca Versailles Chambord

Handle fuel pump - Simca Versailles ChambordDelivered with seal

Head gasket 1.6 mm Simca Versailles Chambord

" 1.6 mm cylinder head gasket for Simca V8 engine" "Aquilon" ". Measured cylinder head thickness Head gasket type 37.3 mm (original) 1.6 mm standard gasket from 37.0 to 37.3 mm 1.6 mm standard gasket from 36.0 to 36.9 ...

Head ignition for RB Ducellier Ford starter Simca Versailles

Head for RB Ducellier distributor, distributor mounted on V8 Simca Versailles, Chambord etc. Can also be mounted on Marmon with petrol V8 equipped with civilian ignition.

Ignition capacitor 6, 12 and 24V

6.12V and 24V compatible ignition capacitor.

Ignition coil 12v standard

Ignition coil guaranteed for use with a 12 V platinum screw igniter (breakers). Impedance respected to prevent the breakers from bluing.Works perfectly also with electronic module or integral electronic igniter. (Non contractual photo)

Ignition coil 12v VALEO

Ignition coil guaranteed for use with a 12 V platinum screw igniter (breakers). Impedance respected to prevent the breakers from bluing.Works perfectly also with electronic module or integral electronic igniter. (Non contractual photo)

Ignition finger igniter RB Ducellier Simca Versailles Chambord

" Finger for igniter mounted on Simca V8. Incompatible with igniter mounted on Ford Vedette. "

Ignition harness V8 Ford Vedette Simca Versailles Chambord

High performance ignition harness, black silicone, interference suppression in accordance with European legislation. Lengths specially adapted for Ford Vedette, Bee V8 engines; Vendôme, Comète, Monte Carlo and Simca Trianon, Versailles, Régence, ...

Ignition set 8 spark plugs V8 Ford Vedette Simca Versailles Chambord

Set of 8 NGK spark plugs for Ford Vedette, Comète, Vendôme, Monte Carlo and Simca Trianon, Versailles, Régence, Beaulieu, Chambord, Présidence, Marly 1 and 2 engines. Thermal index adapted to fuel Lead Free 95 and 98.

IGOL 20W50 mineral oil - 5L can

5 l can (non contractual photo) - Viscosity: 20W-50BenefitsHéRITAGE GTZ mineral oil.Multigrade lubricant for Gasoline and Diesel engines, made from severely refined mineral bases and additives suitable for older engines. The anti-wear additive ...

IGOL Rallye Gear axle transmission oil SAE 75 80 90 - GL4

Oil for gearbox and bridge for old mechanics. Type SAE 75 80 90 - GL4. 1L container.(Not suitable for Peugeot type screw axles)

IGOL semi-synthetic 15W50 oil - 5L can

Can of 5 L.Viscosity: 15W-50BenefitsHéRITAGE ZS semi-synthetic oil.Multigrade lubricant for gasoline engine of tourism, reinforced with synthetic bases, particularly adapted to the old engines, gasoline or diesel, equipped with an oil filter - ...

Kit 3 camshaft bushes x 3 - Simca Versailles Chambord - Aquilon engine

Set of 3 camshaft bushes standard dimension for Aquilon Simca Versailles Chambord engine.Delivered with the tool.

Kit of 12V electric fuel pump

" 12V electric fuel pump. Connects in series with the original fuel line. Keeps the hand pump. Avoids having to lift the hood to turn up gasoline before starting. To be powered through a push button for occasional operation. Low pressure, no need ...

Landing stops - Simca Versailles Chambord

Set of 4 retainers for V8 Ford Vedette 1949 - 52 (Strainer with spring and support on central bearing)

liner Ø 66.04 - semi finished 65.50 - Simca V8 Versailles Chambord

Liner Ø 66.04 - semi finished 65.50 - long 168mm Ø outside 69 mm Ø flange 70 mm height 5mm - Simca V8 Versailles Chambord - sold individually

Manometer Tachometer - 2 - 4 - 6 - 8 cyl - electric 12V - black background - for negative to mass

Mano "OS" Tachometer 0 to 5000 rpm for 4-cylinder petrol engine. Connects to the "break" terminal on the ignition coil. 52 mm recess on the pressure gauge side. delivered with lighting. for negative to ground

Manometer Tachometer - 2 - 4 - 6 - 8 cyl - electric 12V - ivory background - for negative to mass

Mano "OS" Tachometer 0 to 5000 rpm for 4-cylinder petrol engine. Connects to the "break" terminal on the ignition coil. 52 mm recess on the pressure gauge side. delivered with lighting. for negative to ground

Mechanism clutch PKSC - Simca Chambord Versailles

Clutch mechanism reconditioned, in standard exchange mounted on Aquilon Simca V8 engineComplete disassembly, micro balling, surfacing and retaring of the pressure plate.(The sending is done after receipt of the used mechanism, not ...

€297.60 TTC
(248,00 € HT)

Metal body battery switch - safety

Coupe batterie - permet d'isoler électriquement la batterie.

NDIX carburetor gasket - Simca Versailles Chambord

Gasket for NDIX carburetor

Oil filter foot gasket Ford Vedette Simca

Gasket to be placed between the central crankcase and the base of the oil filter. "Y" shaped.

Oil pressure contact mano - 12x150 - Simca Versailles Chambord

oil pressure switch M12x150

Oil seal ring gearbox outlet - Simca V8

Sealing ring (oil seal) for the gearbox outlet.

Oil seal rings gearbox lever - Simca Versailles Chambord

Set of 2 sealing rings (oil seal) for gearbox controls (mounted on control cover).Gaskets to be glued to immobilize them.

Pellet set of 4 - Ford Vedette and Simca engine block

Set of 4 pellets for Vedette Ford and Simca engine block diam. about 44 mm.

Pellets set of 4 - Simca V8 cylinder heads

" Set of 4 Simca Aquilon type cylinder head pellets. diam 18.4 mm approximately (1 pellet per cylinder head) "

Pinion oil pump mounted on axis - Simca Versailles Chambord

Replacement pinion for oil pump - Delivered riveted with new axle - V8 Simca Versailles, Chambord, etc. - Advantageously replaces the celoron one that has become fragile over time.Attention for Ford Vedette V8 12cv 2150 cm3, choose the reference ...

€270.20 TTC
(270,20 € HT)

Pressure hose for igniter Ø 6 mm - by the meter

Hose to connect the igniter / carburetor depression 6 mm sold by the meter.

Reinforced collar for exhaust - Ø 44-47 mm

Reinforced collar for exhaust - Ø 44-47 mmRobust French manufacturing

Reinforced collar for exhaust - Ø 52-55 mm

Reinforced collar for exhaust - Ø 52.55 mmRobust French manufacturing

Reinforced collar for exhaust - Ø 64-67 mm

Reinforced collar for exhaust - Ø 64-67 mmRobust French manufacturing

Ring set Ø 66.50 mm Simca 2.50x2.50x4 - 8cyl

Ring set Ø 66.50 mm Simca 2.50x2.50x4 - 8cyl

Ring set Ø 67.50 mm Simca Chambord 2.38x2.38x5 - 8cyl

Ring set Ø 66.04 mm Simca 2.38x2.38x5 - 8cyl

Ring x 2 - gearbox lever or column foot - Simca Versailles Chambord

Set of 2 repair rings to replace the silent blocks of the gearbox levers or those at the bottom of the column - Simca Versailles Chambord.Requires 2 sets per vehicle

Rod bearings Ford Vedette 53-54 or Simca Chambord - 010 - 44.34 mm

" Set of bearings (16 half-shells) for Ford Vedette 2nd generation 1953-54 and Simca V8 engines. Dimension: .010 US (0.25 mm) Each connecting rod receives its pair of bearings. "

Rod bearings Ford Vedette 53-54 or Simca Chambord - 020 - 44.08 mm

" Set of bearings (16 half-shells) for Ford Vedette 2nd generation 1953-54 and Simca V8 engines. Dimension: .020 US (0.50 mm) Each connecting rod receives its pair of bearings. "

Rod bearings Ford Vedette 53-54 or Simca Chambord - 030 - 43.83 mm

" Set of bearings (16 half-shells) for Ford Vedette 2nd generation 1953-54 and Simca V8 engines. Dimension: .030 US (0.75 mm) Each connecting rod receives its pair of bearings. "

Rod bearings Ford Vedette 53-54 or Simca Chambord - 040 - 43.57 mm

" Set of bearings (16 half-shells) for Ford Vedette 2nd generation 1953-54 and Simca V8 engines. Dimension: .040 US (1 mm) Each connecting rod receives its pair of bearings. "

Rod bearings Ford Vedette 53-54 or Simca Chambord - STD - 44.59 mm

" Set of bearings (16 half-shells) for Ford Vedette 2nd generation 1953-54 and Simca V8 engines. Dimension: STD - 44.59 mm Each connecting rod receives its pair of bearings. "

rubber fuel gauge seal - 3-hole

Rubber seal for 3-hole fuel gauge

Seal on V8 oil filter housing Simca Versailles Chambord

Circular seal for Ford Vedette, Vendôme and Simca Vedette oil filter housing.Mounts on a cover or on a base depending on the model and year.

Segment set Ø 66.04 mm Simca Chambord 2.38x2.38x5 - 8cyl

Segment set Ø 66.04 mm Simca 2.38x2.38x5 - 8cyl

Segment set Ø 66.04 mm Simca Chambord 2.38x2.38x5x5 - 8cyl

Segment set Ø 66.04 mm Simca 2.38x2.38x5x5 - 8cyl

Segment set Ø 66.50 mm Simca 2.38x2.38x5 - 8cyl

Segment set Ø 66.50 mm Simca 2.38x2.38x5 - 8cyl

Segment set Ø 66.80 mm Simca Chambord 2.38x2.38x5 - 8cyl

Segment set Ø 66.80 mm Simca 2.38x2.38x5 - 8cyl

Segment set Ø 67.00 mm Simca Chambord 2.38x2.38x4 - 8cyl

Segment set Ø 67.00 mm Simca 2.38x2.38x4 - 8cyl

Segment set Ø 67.50 mm Simca Chambord 2 x 2 x 5 - 8cyl

Segment set Ø 67.50 mm Simca 2 x2 x 5 - 8cyl

Serflex collar for gasoline hose diam 8 mm

serflex collar 10-16 mm

Set of 2 engine mounts Simca Versailles - Chambord - ARIANE 8 cylinders

Set of 2 engine mounts for V8 Simca.Mounts on Trianon, Versailles, Régence, Beaulieu, Chambord, Présidence, Marly, Ariane 8.

€120.00 TTC
(100,00 € HT)

Set of 34 Simca Chambord V8 cylinder head screws

Set of 34 black phosphated hexagonal head screws - 2 screw lengths in the set. Withstands up to 6 m.kgMounts on Simca Beaulieu, Chambord, Presidency Marly 2.

Set of 8 pistons 66.04 Simca Versailles Chambord

Set of 8 pistons original dimension (66.04 mm) complete (with segments, pins and clips). Aluminum body, quality segmentation with spring-loaded oil scrapers. Flat heads. Mounts on Simca Trianon, Versailles, Régence, Beaulieu, Chambord, ...

Set of 8 pistons 66.50 Simca Versailles Chambord

Set of 8 pistons dimension 66.50 mm, complete (with segments, pins and clips). Aluminum body, quality segmentation with spring-loaded oil scrapers. Flat heads. Mounts on Simca Trianon, Versailles, Régence, Beaulieu, Chambord, Présidence, Marly l ...

Set of 8 pistons 67.00 Simca Versailles Chambord

Set of 8 pistons dimension 67.00 mm, complete (with segments, pins and clips). Aluminum body, quality segmentation with spring-loaded oil scrapers. Flat heads. Mounts on Simca Trianon, Versailles, Régence, Beaulieu, Chambord, Présidence, Marly I ...

Set of 8 pistons 67.50 Simca Versailles Chambord

Set of 8 pistons dimension 67.50 mm, complete (with segments, pins and clips). Aluminum body, quality segmentation with spring-loaded oil scrapers. Flat heads. Mounts on Simca Trianon, Versailles, Régence, Beaulieu, Chambord, Présidence, Marly I ...

Set of Gaskets engine Aquilon - Simca Versailles Chambord

Seal kit produced according to Techni-Tacot requirements. Fit to Simca Versailles, Régence, Trianon, Beaulieu, Chambord, Présidence, Ariane 8 and Marly V8 engines. Contains all the gaskets (2 cylinder head gaskets 1.6 mm thick, water pump, ...

Simca Versailles Chambord air filter + breather sticker

Sticker for air filter and breather cap. Mounts on Simca V8 engine. Sticker

Simca Versailles Chambord disc clutch

Clutch disc reconditioned, in standard exchange for Simca Versailles, Chambord and derivates. Complete disassembly, micro balling and painting. (The sending is done after receipt of the used mechanism, not destroyed)(Depending on the year, ...

€120.00 TTC
(100,00 € HT)

Simca Versailles Chambord gearbox supports

€102.80 TTC
(102,80 € HT)

Simca Versailles Chambord oil pump pinion

Replacement pinion for oil pump - V8 Simca (Versaille, Chambord, etc.). Supplied with 4 rivets. (Advantageously replaces the celoron one which has become fragile over time). Attention for Ford Vedette 12hp 2150 cm3 V8s, choose the reference " ...

€187.00 TTC
(187,00 € HT)

Simca Versailles Chambord water pump plate

Closing plate for water pump housing. Current manufacture in synthetic materials with carbon reinforcement - very solid - no corrosion possible. Mounts in place of the old one.For Simca Trianon, Versailles, Régence, station wagon Marly 1 and 2, ...

Solenoid coil Rushmatic Simca Chambord Presidence

12v solenoid type actuator for Rushmatic. Supplied with connection wire, central rod and dust cover. Mounted on Rushmatic Simca (Rush-Matic)

solid copper cylinder head gasket 2 mm Simca Versailles Chambord

Solid copper cylinder head gasket. Thickness 2 mm. Used with planed cylinder head. For V8 Simca Trianon, Versailles, Régence, Beaulieu, Chambord, Présidence, Marly 1 and 2, Ariane 8. Also exists in 3mm version (available on the shop) Tightening ...

solid copper cylinder head gasket 3mm Simca Versailles Chambord

Solid copper cylinder head gasket. Thickness 3 mm. Used with very planed cylinder head. For V8 Simca Trianon, Versailles, Régence, Beaulieu, Chambord, Présidence, Marly 1 and 2, Ariane 8. Also exists in 2mm version (available on the ...

Spinnaker ring - the complete kit for Simca Versailles Chambord gearbox

Set of 4 rings for input, output and gearbox lever Simca Versailles Chambord

Standard 6V coil ignition

Branded ignition coil guaranteed for use with 6 V platinum-plated igniter (breakers). Impedance respected to prevent the breakers from becoming blue. Also works perfectly with electronic module or integral electronic igniter.

sticker Simca oil filter

Sticker for oil filter and breather plug. Mounts on V8 engine

Support de manomètre

Support métalique, laqué noir pour manomètre standard D52 mm. Prêt à fixé.

Temperature manometer with probe - black background

Mano "OS" temperature indicator (without electrical connection). Direct reading by probe mounted on a radiator hose (high outlet). 52 mm recess on the pressure gauge side.Capillary 1m80. Delivered with lighting and probe for the hose.

Temperature manometer with probe - ivory background

Mano "OS" temperature indicator (without electrical connection). Direct reading by probe mounted on a radiator hose (high outlet). 52 mm recess on the pressure gauge side.Capillary 1m80. Delivered with lighting and probe for the hose.

Universal bearing grease

For greasing bearings - Water resistant

V8 Ford Vedette Simca Versailles Chambord oil filter cartridge

Replacement cartridge for Ford Vedette, Vendôme and Simca Vedette oil filters. Identical to the C4 FRAM model. Info: Delivered without the gasket under the bell (or the cover for the Simca). It is for sale separately: click HERE

Valve guide - set of 4 - Simca Chambord Versailles

set of 4 valve guides - Simca Chambord Versailles - Aquilon 2350 cc engine - 80 and 84 hpNew period parts and checked.

Water plate gasket for Simca Versailles Chambord

Plate seal behind the timing cover