
Bearing 6203 - 17x40x12
Bearing - 17x40x12 waterproof (often used on dynamo, water pump, flywheel center, etc.). Check with the dimensions of your bearing.
(9,00 € HT)
Double pressure gauge holder
Metal support, black lacquered for standard manometer D52 mm. Ready to fix.
(10,00 € HT)
Reinforced collar for exhaust - Ø 52-55 mm
Reinforced collar for exhaust - Ø 52.55 mmRobust French manufacturing
(5,42 € HT)
Electronic regulator for 6V negative ground dynamo
Electronic regulator for 6V negative ground dynamo - Original appearance in ED3 housing.For dynamos with positive excitation.Charge stabilization at 7.4V. Brighter lighting, better battery charge quality, improved ignition voltage.(Exchange standard)
(208,00 € HT)

Head gasket 2 mm solid copper Ford Vedette
Solid copper cylinder head gasket. 2mm thickness. Used with planed cylinder head. Tightening to 5m.kg. Mandatory installation with aerosol sealant, available here a>. Measured cylinder head thickness Head gasket type 37.3 mm ...
(160,40 € HT)
IGOL Rallye Gear axle transmission oil SAE 75 80 90 - GL4
Oil for gearbox and bridge for old mechanics. Type SAE 75 80 90 - GL4. 1L container.(Not suitable for Peugeot type screw axles)
(15,00 € HT)
bearing stops - Ford 1953 to 54
Set of 4 retainers for V8 Ford Vedette 1949 - 52 (Strainer with spring and support on central bearing)
(20,52 € HT)
Fuel gauge - replacement float
Float in synthetic material resistant to current fuels. Used to replace the cork floats on the fuel gauge Length: 1.40" Diameter: 1.14"
(17,72 € HT)
Fuel gauge - replacement plastic float
White plastic float. Used to replace ring gauge floats.
(12,50 € HT)
Ford Vedette bearings - 010 - 53.04 mm
Set of bearings for Vedette Ford 1949 -54 engine. (1 rear flanged bearing + 2 front and central single bearings) Dimension: .010 US (i.e. + / - 0.25 mm)
(675,00 € HT)
Ignition coil 12v VALEO
Ignition coil guaranteed for use with a 12 V platinum screw igniter (breakers). Impedance respected to prevent the breakers from bluing.Works perfectly also with electronic module or integral electronic igniter. (Non contractual photo)
(50,00 € HT)
Head gasket 1.6 mm Ford Vedette standard
" Cylinder head gasket for Ford Vedette 1949 to 1954. One side all copper, the other with copper hems, thickness 1.6 mm approximately Measured cylinder head thickness Head gasket type 37.3 mm (original) 1.6 mm standard gasket from 37.0 ...
(75,00 € HT)
Ford Vedette cylinder head bolt set
Set of 34 hexagon head screws to replace the original studs - 3/8 16f / p unc 2 lengths of screws in the set - Allows easy removal of cylinder heads. Tightening 5 m.kg maximum
(155,20 € HT)
Echappement sangle support renforcé 50 mm
Sangle de suspension pour échappement, caoutchouc armé. entraxe 52 mm pour vis M8 mm.
(9,03 € HT)
Battery switch - safety
Battery isolator - used to electrically isolate the battery. To be placed on a terminal of the battery.
(10,00 € HT)
Support de manomètre
Support métalique, laqué noir pour manomètre standard D52 mm. Prêt à fixé.
(7,94 € HT)
Viewed products
Upper and lower adjustment for Ford vedette front hub
Allows adjustment of the camber on the front axle. When these parts are worn, play appears making it impossible to adjust the geometry of the front axle and making the vehicle's driving imprecise.Sold individually (2 per front hub)
(96,00 € HT)
liner Ø 52 mm semi finished in Ø 51.50 - Simca 5
liner Ø 52 mm delivered semi finished in Ø 51.50 - length 122 mm - Ø 56 - collar Ø 58 - High collar 6 mm. Fitting on Simca 5. Sold individually
(49,05 € HT)
Screen panel, front left skirt closure, Citroen DS until 1967
mud flap behind front fender, under front pillar, with its stainless steel bracket, DS, left
(34,92 € HT)
Spark plug Motorcraft AG 1 x 4
4 x Motocraft AG 1 spark plugs - Ami Super - GS - Simca 1000 See list on photos
(13,75 € HT)
Rubber teat end for brake reservoir
" Flexible connection for brake reservoir. (100% rubber compatible with lockheed and silicone) Must be fitted with the metal insert to prevent tearing and accidental emptying of the liquid reservoir. "
(9,50 € HT)
12v to 6v regulator for temperature, pressure, fuel gauge
This module allows the use of 6V pressure gauges on a 12V vehicle (negative to ground). Mounts on a temperature gauge, pressure, fuel gauge, ...Very practical, it is fixed directly on the supply terminal of the pressure gauge thanks to a hole ...
(30,00 € HT)
Segment set Ø 52 mm - Simca 5 - 2x2x2x3 - 4cyl
Segment set Ø 52 for Simca 5Cutting clearance to be adjusted before assembly. Non-contractual photo - no return or refund possible.
(132,20 € HT)