12V electric fuel pump

" 12V electric fuel pump. Connects in series with the original fuel line. Keeps the hand pump. Avoids having to lift the hood to turn up gasoline before starting. To be powered through a push button for occasional operation. Low pressure, no need ...

12v to 6v regulator for temperature, pressure, fuel gauge

This module allows the use of 6V pressure gauges on a 12V vehicle (negative to ground). Mounts on a temperature gauge, pressure, fuel gauge, ...Very practical, it is fixed directly on the supply terminal of the pressure gauge thanks to a hole ...

160 mm float fuel gauge - 6V

" Float fuel gauge. Adaptable model. Arm length approx. 160 mm. External diameter of plate 54 mm - fixing center distance 38 mm. Supplied with cork seal. 3-hole fixing. Internal resistance approx. 110 ohms. For 6-volt vehicle only. "

6 CYL ENGINE KIT - CITROEN TRACTION 15 CV

Complete engine gasket set, including cylinder head gasket for Citroën Traction 15.

6V electric fuel pump

6V electric fuel pump. To be connected to the ignition coil power supply. Connects in series with the original fuel line.Allows you to keep the manual pump. Avoids having to lift the hood to turn up gasoline before starting.Is intended to remain ...

Aerosol gasket for cylinder head

Sealing spray varnish to be sprayed on both sides of a cylinder head gasket. Improves sealing, essential with solid copper gaskets (any thickness)

Aviation collex type paste gasket for cylinder head - 117ml

Sealing paste to be applied on both sides of a cylinder head gasket. Product similar to "Collex". Leave to evaporate for about 30 min at room temperature after application, then fit the gasket - improves the seal - recommended with solid copper ...

Aviation collex type paste gasket for cylinder head - 450ml

Sealing paste to be applied on both sides of a cylinder head gasket. Product similar to "Collex". Leave to evaporate for about 30 min at room temperature after application, then fit the gasket - improves the seal - recommended with solid copper ...

Axe 8 mm avec papillon pour réparation carburateur Solex 32 PBIC ou similaire

Axle 8.5 mm Ø repair - without butterfly - Solex 32 PBIC or similarsimilar

Shaft dimension repair 8.5 mm without butterfly for repair carburettor Solex 32 PBIC or similarOverall length 91.5 mm

Battery switch - safety

Battery isolator - used to electrically isolate the battery. To be placed on a terminal of the battery.

Battery switch with key - security

Battery switch with key - security

Bearing 6203 - 17x40x12

Bearing - 17x40x12 waterproof (often used on dynamo, water pump, flywheel center, etc.). Check with the dimensions of your bearing.

Bearing bearings 53.50mm - dimension 0.50 - without cheek - Citroen HY

Bearing bearings dimension 0.50 -For HY H72 or H78 engine

Bearing bearings dimension 49.00 mm (1.00) - Citroen Traction HY U23

Bearing bearings dimension 49.00 (1.00) -Citroen:- Traction Perfo and 11D  - HY until 1963 ("Traction" type engine)- U23

Bearing bearings dimension 49.25 mm (0.75) - Citroen Traction HY U23

Bearing bearings dimension 49.25 (0.75) -Citroen: a- Traction Perfo and 11D  - HY until 1963 ("Traction" type engine)- U23

Bearing bearings dimension 49.50 mm (0.50) - Citroen Traction HY U23

Bearing bearings dimension 49.50 (0.50) -Citroen:- Traction Perfo and 11D  - HY until 1963 ("Traction" type engine)- U23

Bearing bearings dimension 49.75 mm (0.25) - Citroen Traction HY U23

Bearing bearings dimension 49.75 (0.25) -Citroen:- Traction Perfo and 11D  - HY until 1963 ("Traction" type engine)- U23

Bearing bearings dimension 50.00 mm (STD) - Citroen Traction HY U23

Bearing bearings dimension 50.00 (STD) -Citroen:- Traction Perfo and 11D  - HY until 1963 ("Traction" type engine)- U23

Bearings 54.00mm - STD dimension - without cheek - Citroen HY

Bearing bearings dimension 50.00 (STD) -For ID 19 engine and similar engine block

BENDIX launcher for starter - CItroen Traction

BENDIX launcher for starter - CItroen Traction

Breather for cylinder head cover - Citroen HY

Breather for cylinder head cover - Citroen HYPetrol engine from 1963

Calibrouge (Plastigage) mechanical clearance measurement

"Plastigage"The Calibrouge ("plastigage or plastigauge") is a simple and practical tool for measuring the clearances of your bearings. Range of use: operating clearance from 0.025 to 0.175 mm

Carburateur similaire au type Solex 34 PBIC Traction Citroen et ID 19

Carburateur neuf type Solex 34 PBIC. Prise de dépression sur embase de pied. Configuration pour Citroen Traction - ID 19 Buse 27 - Gicleur principal 140 et ajutage automaticité 165 - Emulsion19 - Ralenti 50 - air ralenti 130 - Pointeau 1.5 - ...

Carburetor similar to the Solex 32 PBIC Traction Citroen type

New carburettor similar to the Solex 32 PBIC type. Vacuum outlet on foot base. Configuration for Citroen TractionNozzle 26 - Main jet 135 and automatic nozzle 190 - Emulsion19 - Idle 50 - idle air 130 - Needle 1.5 - Float 12.5 gr - Accelerator ...

Cast iron cylinder head exhaust gasket

Exhaust manifold gasket for cast iron cylinder head -Hy and Traction 11cv until 19632 seals are required per vehicle

Charger and maintenance 6v / 12v Accumate

AccuMate is designed to automatically charge and monitor batteries without the danger of overcharging them, regardless of plug-in time. AccuMate is available for all 6V and 12V lead acid batteries, making it a perfect accessory for owners of ...

Citroen HY U23 Traction timing chain

Distribution chain. Non contractual photo.

Citroën Traction 11D engine cover

Engine seal kit for Citroen Traction 11D engine(fitted with cast iron cylinder head and sheet metal cylinder head cover).

Citroen traction disc clutch

Clutch disc reconditioned, in standard exchange Traction, type H, HY, U23 and derivatives. Complete disassembly, micro balling and painting. (The sending is done after receipt of the used mechanism, not destroyed)(Depending on the year, ...

€132.00 TTC
(110,00 € HT)

Citroën Traction gearbox outlet repair sleeve

Repair sleeve (speedi sleeve) for gearbox outlet. To slide on the worn part to repair the worn part (marked) by the spinnaker. Fit new spinnakerFor one side.

Citroën traction mechanism clutch

Clutch mechanism reconditioned, in standard exchange mounted on Citroën Traction engine, Type H, HY, U23 and derivatives. Complete disassembly, micro balling, surfacing and retaring of the pressure plate. p > (The sending is done after ...

€396.00 TTC
(330,00 € HT)

Clutch thrust ball bearing for 3-latch mechanism - Traction Citroen

Bearing for clutch release associated with the 3-latch mechanism and heavy plate.(Depending on year, non-contractual photo)

€90.00 TTC
(75,00 € HT)

Complete set of solex 32 pbic carburetor gaskets

Solex 32 pbic carburetor gaskets kit - accelerator pump diaphragm included (Colorale, Goélette, R2087, Frigate, etc) Version with manual starter

Connecting rod bearings (set) 47.00 mm dimension 1.00 - Citroen Traction 11D - HY -U23

Conrod bearing set 47.00 mm - dimension 1.00 mm - Citroen Traction 11D - HY - U23Mounts on engines equipped with bearing connecting rods.

Connecting rod bearings (set) 47.50 mm dimension 0.50 - Citroen Traction 11D - HY -U23

Set of 47.50 mm connecting rod bearings - dimension 0.50 mm - Citroen Traction 11D - HY - U23Mounts on engines equipped with bearing connecting rods.

Connecting rod bearings (set) 47.75 mm dimension 0.25 - Citroen Traction 11D - HY - U23

Set of 47.75 mm connecting rod bearings - dimension 0.25 mm - Citroen Traction 11D - HY - U23Mounts on engines equipped with bearing connecting rods.

Connecting rod bearings (the set) dimension 0.75 mm - Citroen Traction 11D - HY -U23

Set of 47.25 mm connecting rod bearings - dimension 0.75 mm - Citroen Traction 11D - HY - U23Mounts on engines equipped with bearing connecting rods.

Crankcase gasket strip 6.5 MM 11CV 11D / HY

Crankcase gasket strip 6.5 MM 11CV 11D / HY6.5x0.5mm

Dark green engine paint RAL 6005 - 500 ml

Dark green engine paint RAL 6005 -Pot of 500 mlSuitable for engines, housings, gearboxes, differentials, brake drums and all parts subject to heating in cast iron, steel and light alloys.Direct application on degreased metal (or better, treated ...

€40.80 TTC
(34,00 € HT)

Disc clutch kit + mechanism + thrust bearing in standard exchange Citroen Traction 15CV

Disc clutch kit + mechanism + thrust bearing in standard exchange Citroen Traction 15CV

€772.00 TTC
(643,33 € HT)

Double pressure gauge holder

Metal support, black lacquered for standard manometer D52 mm. Ready to fix.

Echappement sangle support renforcé 50 mm

Sangle de suspension pour échappement, caoutchouc armé. entraxe 52 mm pour vis M8 mm.

Electronic ignition - Citroën HY

123 Ignition electronic ignition for Citroën Type H 4 cylinders, "Perfo" or "11D" engine.Installs in place of your original model. Everything is integrated in the body of the igniter (no remote box).Supplied with adjustment and assembly ...

Electronic ignition amplifier assistance module - 12V negative to earth

Electronic ignition assistance module. Allows for more energetic spark plug ignition, improved starting, smoother pick-up, helps reduce fuel consumption and consequently pollution.The breakers (platinum-plated screws) are left in place - the ...

Electronic ignition amplifier assistance module - 6V negative to earth

Electronic ignition assistance module. Allows more energetic spark plug ignition, improves starting, smoother times, helps reduce fuel consumption and consequently pollution.The breakers (platinum screws) are left in place - the original coil can ...

Embrayage - kit mécanisme diaphragme +disque +butée - Citroen Traction 11cv

Engine paint black RAL 9005 - 500 ml

Black paint - 500 ml jarSuitable for engines, housings, gearboxes, differentials, brake drums and all parts subject to heating in cast iron, steel and light alloys.Direct application on degreased metal (or better, treated with our Phosprim 4090), ...

€40.80 TTC
(34,00 € HT)

Engine paint oxide green RAL 6020 - 500 ml

Engine paint oxide green RAL 6020 -Pot of 500 mlSuitable for engines, housings, gearboxes, differentials, brake drums and all parts subject to heating in cast iron, steel and light alloys.Direct application on degreased metal (or better, treated ...

€40.80 TTC
(34,00 € HT)

Engine red paint - 500 ml -

Engine red paint -Pot of 500 mlSuitable for engines, housings, gearboxes, differentials, brake drums and all parts subject to heating in cast iron, steel and light alloys.Direct application on degreased metal (or better, treated with our Phosprim ...

€40.80 TTC
(34,00 € HT)

Exhaust manifold paint - 250 ml

€48.00 TTC
(40,00 € HT)

Exhaust support strap reinforces 90 mm

Suspension strap for exhaust. Robust construction, reinforced rubber, metal eyelets.92 mm center distance for M8 mm screws.

Exhaust suspension ring 63x96 width 27 mm - Peugeot 203

Suspension ring for Peugeot 203 exhaust and othersDimension approximately 63 x 96 x width 27 mm

Ford RAL 5005 blue engine paint - 500 ml

Ford RAL 5005 blue engine paint - 500 ml jarSuitable for engines, housings, gearboxes, differentials, brake drums and all parts subject to heating in cast iron, steel and light alloys.Direct application on degreased metal (or better, treated with ...

€40.80 TTC
(34,00 € HT)

fuel filter Big size ø 6 and 8 mm

Paper fuel filter for 6 or 8 mm hose.

fuel filter ø 6 and 8 mm

Paper fuel filter for 6 or 8 mm hose.

Fuel gauge - replacement float

Float in synthetic material resistant to current fuels. Used to replace the cork floats on the fuel gauge Length: 1.40" Diameter: 1.14"

Fuel gauge - replacement plastic float

White plastic float. Used to replace ring gauge floats.

Fuel gauge with float 6V - Traction

" 6 volt float fuel gauge for Traction. "

Fuel hose diam 8 mm - by the meter

8 mm fuel hose sold by the meter.

Fuel needle - Solex 32 PBIC carburettor or similar

Fuel needle - Solex 32 PBIC carburettor or similar

Fuel pump - 6V or 12V control push button

6 or 12v 10A push button. Can be used to activate an electric fuel pump for a few seconds, for example.

Fuel pump - angled outputs - Citroen type Traction - U23 - HY

Fuel pump with primer, for Citroën Traction, delivered with gasket. Can also be mounted on U23 gasoline engine, HY, type H, and HZ equipped with the engine type Traction.

Fuel pump - GUIOT 90 mm diaphragm kit Citroen Traction U23 HY

Replacement diaphragm for GUIOT fuel pump (Citroen Traction U23 HY engine). Ø 90mm. Supplied with membrane and gaskets. (check the type of pump before ordering)

Fuel pump - Horiz outlets - Citroen type Traction - U23 - HY

Fuel pump with primer, for Citroën Traction, delivered with gasket. Can also be mounted on U23 gasoline engine, HY, type H, and HZ equipped with the engine type Traction.

gasket for solex 32 pbic carburetor

2 x paper gaskets for Solex 32 pbi carburetor base.Fixing center distance: 60 mmCentral passage: 32 mmTotal length: 78 mmwidth: 50mm

Gasket paste for motor - auto extrudable cartridge 200 ml

Mot. Silicone gasket & self-extruding housing RTV K164     high-quality, heat-resistant silicone     base: modified oxime silicone (acid-free hardening system)

Gauge Gasket cork 3 holes

Cork gasket for 3-hole fuel gauge

Gearbox or axle oil SAE 80-140 - IGOL - 1L

Viscosity index 80 - 140API GL-4(Not suitable for Peugeot type screw axles)

Ignition - Citroen Traction U23 engine silicone harness

Ignition harness (5 wires) for Citroën Traction engine, U23. Highly recommended with electronic ignition.Wire with red silicone insulator, works with platinum screws or electronic ignition, current manufacture (not from old stocks).

Ignition - complete igniter with vacuum - M48

Complete igniter with vacuum capsule AND centrifugal advance - similar curve Ducellier M48 - maximum advance 12 ° on igniter - delivered tested and greased. Dimensions :- length between shoulder (stop under the body) and end of trainer: 64mm- ...

Ignition capacitor 6, 12 and 24V

6.12V and 24V compatible ignition capacitor.

Ignition coil 12v standard

Ignition coil guaranteed for use with a 12 V platinum screw igniter (breakers). Impedance respected to prevent the breakers from bluing.Works perfectly also with electronic module or integral electronic igniter. (Non contractual photo)

Ignition coil 12v VALEO

Ignition coil guaranteed for use with a 12 V platinum screw igniter (breakers). Impedance respected to prevent the breakers from bluing.Works perfectly also with electronic module or integral electronic igniter. (Non contractual photo)

Ignition coil 6V - High Performance

Bosch, NGK or Béru High Performance type ignition coil, guaranteed for use with:- 6 V platinum-plated screw igniter (breakers),- electronic ignition type 123 ignition,- platinum screw igniter + electronic amplification module

Ignition finger igniter Ducellier 65mm

Finger for Ducellier distributor equipped with a 65mm headMounts with Ducellier 65 mm head

Ignition head Ducellier 65 mm

Head for Ducellier distributor: Interlocking inside the head = 65 mm, outside about 72 mm.To be assembled with breakers 1 237 013 808, and ducellier finger.

Ignition Set of 4 Citroen Traction U23 HY spark plugs

Set of 4 NGK standard base spark plugs (14mm), Citroen U23, Traction, HY, type H engine. Compatible with SP95 and SP98 fuels.

Ignition set of Ducellier breakers

Set of breakers for Ducellier distributor For Renault Prairie, R2087, Goélette and derivatives

Ignition set of SEV breakers

" Set of breakers for SEV igniter For Renault Prairie, R2087, Goélette and derivatives "

IGOL 20W50 mineral oil - 5L can

5 l can (non contractual photo) - Viscosity: 20W-50BenefitsHéRITAGE GTZ mineral oil.Multigrade lubricant for Gasoline and Diesel engines, made from severely refined mineral bases and additives suitable for older engines. The anti-wear additive ...

IGOL Rallye Gear axle transmission oil SAE 75 80 90 - GL4

Oil for gearbox and bridge for old mechanics. Type SAE 75 80 90 - GL4. 1L container.(Not suitable for Peugeot type screw axles)

IGOL semi-synthetic 15W50 oil - 5L can

Can of 5 L.Viscosity: 15W-50BenefitsHéRITAGE ZS semi-synthetic oil.Multigrade lubricant for gasoline engine of tourism, reinforced with synthetic bases, particularly adapted to the old engines, gasoline or diesel, equipped with an oil filter - ...

Kit of 12V electric fuel pump

" 12V electric fuel pump. Connects in series with the original fuel line. Keeps the hand pump. Avoids having to lift the hood to turn up gasoline before starting. To be powered through a push button for occasional operation. Low pressure, no need ...

Manometer Tachometer - 2 - 4 - 6 - 8 cyl - electric 12V - black background - for negative to mass

Mano "OS" Tachometer 0 to 5000 rpm for 4-cylinder petrol engine. Connects to the "break" terminal on the ignition coil. 52 mm recess on the pressure gauge side. delivered with lighting. for negative to ground

Manometer Tachometer - 2 - 4 - 6 - 8 cyl - electric 12V - ivory background - for negative to mass

Mano "OS" Tachometer 0 to 5000 rpm for 4-cylinder petrol engine. Connects to the "break" terminal on the ignition coil. 52 mm recess on the pressure gauge side. delivered with lighting. for negative to ground

Metal body battery switch - safety

Coupe batterie - permet d'isoler électriquement la batterie.

New connecting rod for mounting with bearing - Citroen HY engine ID19

New connecting rod for assembly with bearing - Citroen Traction 11hp and 15hp and HY engine ID 19 current 63 and end of series.Supplied without pad. It is advisable to replace all 4 connecting rods at the same time.

Oil pressure switch - Citroen

Oil pressure switch Citroen. Thread 14x150.

paper gasket x 2 + thermal wedge for solex 32 pbic carburetor

kit 2 joints papier + cale thermique pour embase de carburateur Solex 32 pbi.  

Piston ring set Ø 78 mm Citroen Traction U23 HY 2.5x2.5x4x4 - 4 cyl

Piston ring set Ø 78 mm Citroen Traction U23 HY 2.5x2.5x4x4 - 4 cyl

Pressure hose for igniter Ø 5.5 mm - by the meter

Hose to connect the igniter / carburetor depression 5.5 mm sold by the meter.

Reinforced collar for exhaust - Ø 44-47 mm

Reinforced collar for exhaust - Ø 44-47 mmRobust French manufacturing

Reinforced collar for exhaust - Ø 52-55 mm

Reinforced collar for exhaust - Ø 52.55 mmRobust French manufacturing

Reinforced collar for exhaust - Ø 64-67 mm

Reinforced collar for exhaust - Ø 64-67 mmRobust French manufacturing

Repair kit for gasoline pump SEV - Renault Fregate Prairie Goelette Galion

Repair kit for SEV D100mm fuel pump. Fitted on Renault Frégate Prairie Goelette Galion. Please check the brand of your pump before ordering

Rod bearings (set) 48 mm STD side - Citroen Traction 11D - HY - U23

Set of 48.00 mm connecting rod bearings - original STD dimension - Citroen Traction 11D - HY - U23Mounts on engines equipped with bearing connecting rods.

rubber fuel gauge seal - 3-hole

Rubber seal for 3-hole fuel gauge

Sealing plate bearing cap 11CV PERFO - Citroen Traction U23 HY

Sealing plate bearing cap 11CV PERFO - Citroen Traction U23 HY

Segment set Ø 78 mm Citroen Traction U23 HY 3x3x3x4.5 - 4cyl

Segment set Ø 78 mm Citroen Traction 3x3x3x4.5 - 4cyl

Segments set Ø 72 mm Citroen Traction U23 HY 2x2.5x5 - 4cyl

Piston ring set Ø 72 mm Citroen Traction 2 x 2.5 x 5 - 4 cyl

Serflex collar for gasoline hose diam 8 mm

serflex collar 10-16 mm

Set of 13 cylinder head bolts 10x102x24 Perfo engine - Citroen Traction U23 HY

Set of 13 cylinder head screws 10x102x24 Perfo engine - Citroen Traction U23 HY

Set of 3 25mm pellets for cast iron cylinder head - Citroen Traction U23 HY

Set of 3 Ø25mm pellets only for cast iron cylinder head - Citroen Traction U23 HY

Set of 4 30mm pellets for cast iron cylinder head - Citroen Traction U23 HY

Set of 4 Ø30mm pellets only for cast iron cylinder head - Citroen Traction U23 HY

Set of 4 Cylinder liner gasket ring - Citroen Traction U23 HY

Set of 4 single liner base gaskets - Citroen Traction U23 HY

Set of 8 external valve springs - cast iron cylinder head - Citroen Traction HY U23

Set of 8 external valve springs - cast iron cylinder head - Citroen Traction HY U23

Set of 8 inner valve springs - cast iron cylinder head - Citroen Traction HY U23

Set of 8 inner valve springs - cast iron cylinder head - Citroen Traction HY U23

Set of flat piston liners 78mm - Citroen Traction - U23

Set of 4 liners + 4 complete flat head pistons (segments, clips, pins) - Quality segments.Non contractual photo

Set of flat pistons liners 78mm - Citroen Traction 15 cv

Set of 6 liners + 6 complete flat head pistons (segments, clips, pins) - Quality segments.Non contractual photo

SEV finger ignition large model

Finger for SEV igniter (large model)

Shaft 8.5 mm Ø repair - repair Solex 32 PBIC carburettor or similar

Shaft dimension repair 8.5 mm with butterfly for repair carburettor Solex 32 PBIC or similarOverall length 91.5 mm

Stainless steel cylinder head tube Citroen Traction - HY - U23

Water tube for cooling cast iron cylinder head. Citroen Traction, HY, U23 and derivativesStainless steel construction

Standard 6V coil ignition

Branded ignition coil guaranteed for use with 6 V platinum-plated igniter (breakers). Impedance respected to prevent the breakers from becoming blue. Also works perfectly with electronic module or integral electronic igniter.

Support de manomètre

Support métalique, laqué noir pour manomètre standard D52 mm. Prêt à fixé.

Temperature manometer with probe - black background

Mano "OS" temperature indicator (without electrical connection). Direct reading by probe mounted on a radiator hose (high outlet). 52 mm recess on the pressure gauge side.Capillary 1m80. Delivered with lighting and probe for the hose.

Temperature manometer with probe - ivory background

Mano "OS" temperature indicator (without electrical connection). Direct reading by probe mounted on a radiator hose (high outlet). 52 mm recess on the pressure gauge side.Capillary 1m80. Delivered with lighting and probe for the hose.

Universal bearing grease

For greasing bearings - Water resistant

Valve guide Ø 9 X 13.06 X 55 - CITROeN Traction 11 - HY - U23

Valve guide Ø 9 X 13.06 X 55 - CITROËN Traction 11 - HY - U23 -Cast iron material

Valves x 4 - ADM Ø 37x9x101.6 - Citroen Traction 11 perfo - HY Perfo engine - U23 flat wings

Set of 4 ADM valves Ø 37x9x101.6 - Citroen Traction 11 perfo - HY from 1955 to 63 Perfo engine - U23 flat wings

Valves x 4 - ADM Ø 37x9x109 - plate - Citroen Traction 11D

Set of 4 ADM valves Ø 37x9x109 - flat - Citroen Traction 11D

Valves x 4 - ECH Ø 33.8x9x103 - Citroen Traction 11 perfo - HY Perfo engine - U23 flat wings

Set of 4 ECH valves Ø 33.8x9x103 - Citroen Traction 11 perfo - HY Perfo engine 1955 to 63 - U23 flat wings

Valves x 4 - ECH Ø 34x9x112.7 - Citroen Traction 11D

Set of 4 ECH valves Ø 34x9x112.7 - Citroen Traction 11D