
Ford RAL 5005 blue engine paint - 500 ml
Ford RAL 5005 blue engine paint - 500 ml jarSuitable for engines, housings, gearboxes, differentials, brake drums and all parts subject to heating in cast iron, steel and light alloys.Direct application on degreased metal (or better, treated with ...
(34,00 € HT)

Carburetor gasket Stromberg Ford Vedette
Gasket for 22.2 Stromberg carburettor
(16,50 € HT)
Exhaust - Y tube - 2 in 1 stainless steel - Ford Vedette
Stainless steel exhaust - Y connecting the 2 cast iron manifolds to line. Ford Vedette 1949 to 1954.
(363,67 € HT)

Set of 8 pistons 66.04 Ford Vedette
Set of 8 pistons - New manufacture, similar to the original model - reduction in piston mass (approximately 255 gr with rings) - molybdenum treatment - cylinder dimension 66.04 mm. Supplied with segments, pins and circlips - The segments supplied ...
(1 290,00 € HT)
Ford 53 and 54 crankshaft bearing screws
Set of bearing screws for V8 Ford Vedette model 1953 and 1954
(134,42 € HT)
6V electric fuel pump
6V electric fuel pump. To be connected to the ignition coil power supply. Connects in series with the original fuel line.Allows you to keep the manual pump. Avoids having to lift the hood to turn up gasoline before starting.Is intended to remain ...
(75,00 € HT)
Standard 6V coil ignition
Branded ignition coil guaranteed for use with 6 V platinum-plated igniter (breakers). Impedance respected to prevent the breakers from becoming blue. Also works perfectly with electronic module or integral electronic igniter.
(36,00 € HT)
IGOL Rallye Gear axle transmission oil SAE 75 80 90 - GL4
Oil for gearbox and bridge for old mechanics. Type SAE 75 80 90 - GL4. 1L container.(Not suitable for Peugeot type screw axles)
(15,00 € HT)
Fuel pump - 6V or 12V control push button
6 or 12v 10A push button. Can be used to activate an electric fuel pump for a few seconds, for example.
(8,25 € HT)
Calibrouge (Plastigage) mechanical clearance measurement
"Plastigage"The Calibrouge ("plastigage or plastigauge") is a simple and practical tool for measuring the clearances of your bearings. Range of use: operating clearance from 0.025 to 0.175 mm
(22,50 € HT)
Oil seal rings gearbox lever - Simca Versailles Chambord
Set of 2 sealing rings (oil seal) for gearbox controls (mounted on control cover).Gaskets to be glued to immobilize them.
(12,00 € HT)
Rod bearings Ford Vedette 53-54 or Simca Chambord - 040 - 43.57 mm
" Set of bearings (16 half-shells) for Ford Vedette 2nd generation 1953-54 and Simca V8 engines. Dimension: .040 US (1 mm) Each connecting rod receives its pair of bearings. "
(390,00 € HT)
Head ignition for RB Ducellier Ford starter Simca Versailles
Head for RB Ducellier distributor, distributor mounted on V8 Simca Versailles, Chambord etc. Can also be mounted on Marmon with petrol V8 equipped with civilian ignition.
(45,00 € HT)
Water pump repair kit with aluminum impeller - Ford Vedette
Repair kit for water pump for "Y" or "T" pump body - years 1949-54. New axle is 16mm instead of 12 mm. So you need to drill body 16.5 mm. We recommend correcting the seat of the rotating joint at the back of the body.
(151,20 € HT)
Battery switch - safety
Battery isolator - used to electrically isolate the battery. To be placed on a terminal of the battery.
(10,00 € HT)
Viewed products
Screen panel, front left skirt closure, Citroen DS until 1967
mud flap behind front fender, under front pillar, with its stainless steel bracket, DS, left
(34,92 € HT)
Spark plug Motorcraft AG 1 x 4
4 x Motocraft AG 1 spark plugs - Ami Super - GS - Simca 1000 See list on photos
(13,75 € HT)
Rubber teat end for brake reservoir
" Flexible connection for brake reservoir. (100% rubber compatible with lockheed and silicone) Must be fitted with the metal insert to prevent tearing and accidental emptying of the liquid reservoir. "
(9,50 € HT)
12v to 6v regulator for temperature, pressure, fuel gauge
This module allows the use of 6V pressure gauges on a 12V vehicle (negative to ground). Mounts on a temperature gauge, pressure, fuel gauge, ...Very practical, it is fixed directly on the supply terminal of the pressure gauge thanks to a hole ...
(30,00 € HT)
Segment set Ø 52 mm - Simca 5 - 2x2x2x3 - 4cyl
Segment set Ø 52 for Simca 5Cutting clearance to be adjusted before assembly. Non-contractual photo - no return or refund possible.
(132,20 € HT)
Segment set Ø 72 mm Simca 2.5x2.5x2.5x4 - 4cyl
Segment set Ø 72 mm Simca 2.5x2.5x2.5x4 - 4cyl
(75,00 € HT)
Segment set Ø 74 mm Simca 2.5x2.5x2.5x4 - 4cyl
Segment set Ø 74 mm Simca 2.5x2.5x2.5x4 - 4cyl
(100,95 € HT)
Pistons complets - jeu de 4 - Ø 52.00 mm - Simca 5
Set of 4 piston Ø 52.00 mm - Simca 5
(540,00 € HT)