12V electric fuel pump

" 12V electric fuel pump. Connects in series with the original fuel line. Keeps the hand pump. Avoids having to lift the hood to turn up gasoline before starting. To be powered through a push button for occasional operation. Low pressure, no need ...

160 mm float fuel gauge - 6V

" Float fuel gauge. Adaptable model. Arm length approx. 160 mm. External diameter of plate 54 mm - fixing center distance 38 mm. Supplied with cork seal. 3-hole fixing. Internal resistance approx. 110 ohms. For 6-volt vehicle only. "

6V electric fuel pump

6V electric fuel pump. To be connected to the ignition coil power supply. Connects in series with the original fuel line.Allows you to keep the manual pump. Avoids having to lift the hood to turn up gasoline before starting.Is intended to remain ...

Accelerator pump kit for Stromberg 22.2 Ford Vedette carburettor

Accelerator pump kit for Stromberg 22.2 carburettor. Dimensions shown in the photo. Fitting on Ford Vedette.

Aerosol gasket for cylinder head

Sealing spray varnish to be sprayed on both sides of a cylinder head gasket. Improves sealing, essential with solid copper gaskets (any thickness)

Aviation collex type paste gasket for cylinder head - 117ml

Sealing paste to be applied on both sides of a cylinder head gasket. Product similar to "Collex". Leave to evaporate for about 30 min at room temperature after application, then fit the gasket - improves the seal - recommended with solid copper ...

Aviation collex type paste gasket for cylinder head - 450ml

Sealing paste to be applied on both sides of a cylinder head gasket. Product similar to "Collex". Leave to evaporate for about 30 min at room temperature after application, then fit the gasket - improves the seal - recommended with solid copper ...

Battery switch - safety

Battery isolator - used to electrically isolate the battery. To be placed on a terminal of the battery.

Battery switch with key - security

Battery switch with key - security

Bearing 6203 - 17x40x12

Bearing - 17x40x12 waterproof (often used on dynamo, water pump, flywheel center, etc.). Check with the dimensions of your bearing.

Calibrouge (Plastigage) mechanical clearance measurement

"Plastigage"The Calibrouge ("plastigage or plastigauge") is a simple and practical tool for measuring the clearances of your bearings. Range of use: operating clearance from 0.025 to 0.175 mm

Charger and maintenance 6v / 12v Accumate

AccuMate is designed to automatically charge and monitor batteries without the danger of overcharging them, regardless of plug-in time. AccuMate is available for all 6V and 12V lead acid batteries, making it a perfect accessory for owners of ...

Clutch disc 230mm - standard exchange - Ford Vendome - Montecarlo

Disque d'embrayage reconditionné - en échange standard.  

€144.00 TTC
(120,00 € HT)

Dark green engine paint RAL 6005 - 500 ml

Dark green engine paint RAL 6005 -Pot of 500 mlSuitable for engines, housings, gearboxes, differentials, brake drums and all parts subject to heating in cast iron, steel and light alloys.Direct application on degreased metal (or better, treated ...

€40.80 TTC
(34,00 € HT)

Double pressure gauge holder

Metal support, black lacquered for standard manometer D52 mm. Ready to fix.

Echappement sangle support renforcé 50 mm

Sangle de suspension pour échappement, caoutchouc armé. entraxe 52 mm pour vis M8 mm.

Electric Easy Drive power steering kit

Electronic flasher unit 6V + on ground - Ford Vedette

Electronic flasher unit 6V + on ground - Simca Versailles

Electronic flasher unit 6V + to ground - Ford Vedette - Simca Versailles4 wires Simca Versailles 6 V (1 repeater on the dashboard)

Electronic ignition amplifier assistance module - 6V positive to earth

Electronic ignition assistance module. Allows more energetic spark plug ignition, improves starting, smoother times, helps reduce fuel consumption and consequently pollution.The breakers (platinum-plated screws) are left in place. The original ...

Engine paint black RAL 9005 - 500 ml

Black paint - 500 ml jarSuitable for engines, housings, gearboxes, differentials, brake drums and all parts subject to heating in cast iron, steel and light alloys.Direct application on degreased metal (or better, treated with our Phosprim 4090), ...

€40.80 TTC
(34,00 € HT)

Engine paint oxide green RAL 6020 - 500 ml

Engine paint oxide green RAL 6020 -Pot of 500 mlSuitable for engines, housings, gearboxes, differentials, brake drums and all parts subject to heating in cast iron, steel and light alloys.Direct application on degreased metal (or better, treated ...

€40.80 TTC
(34,00 € HT)

Engine red paint - 500 ml -

Engine red paint -Pot of 500 mlSuitable for engines, housings, gearboxes, differentials, brake drums and all parts subject to heating in cast iron, steel and light alloys.Direct application on degreased metal (or better, treated with our Phosprim ...

€40.80 TTC
(34,00 € HT)

Exhaust - outlet tube + stainless steel stock - Ford Vendome - MONTE CARLO

"Outlet tube with bracket (passage of the bridge) to be connected to the outlet of the silencer. Ford Vendôme and Monte Carlo.All stainless steel."

€372.00 TTC
(310,00 € HT)

Exhaust - round stainless steel silencer - Ford Vendome - MONTE CARLO

Stainless steel silencer for Ford Vendôme and Monté Carlo. French manufacture.

€546.00 TTC
(455,00 € HT)

Exhaust - Y tube - 2 in 1 stainless steel - Ford Vendome - MONTE CARLO

Stainless steel exhaust - Y connecting the 2 cast iron manifolds to line. Ford Vendôme and Monte Carlo.

€414.00 TTC
(345,00 € HT)

Exhaust manifold paint - 250 ml

€48.00 TTC
(40,00 € HT)

Exhaust support strap reinforces 90 mm

Suspension strap for exhaust. Robust construction, reinforced rubber, metal eyelets.92 mm center distance for M8 mm screws.

Exhaust suspension ring 63x96 width 27 mm - Peugeot 203

Suspension ring for Peugeot 203 exhaust and othersDimension approximately 63 x 96 x width 27 mm

Ford and Simca Vedette rod stopper

Set of 16 retainers for V8 Simca or Ford Vedette connecting rod. V8 12 and 13cvOriginally compliant

Ford RAL 5005 blue engine paint - 500 ml

Ford RAL 5005 blue engine paint - 500 ml jarSuitable for engines, housings, gearboxes, differentials, brake drums and all parts subject to heating in cast iron, steel and light alloys.Direct application on degreased metal (or better, treated with ...

€40.80 TTC
(34,00 € HT)

Ford Vedette air filter + breather sticker

" Sticker for air filter and breather cap. Mounts on Ford V8 Vedette, Vendôme, Cometer, Monte Carlo etc. Sticker "

Ford Vedette Stromberg 22.2 Carburetor Kit

Overhaul kit for Stromberg 22.2 (2x30 mm) carburetor. Delivered with complete recovery pump. Fitting on Ford Vedette.

Ford Vedette V8 oil filter housing seal

Circular seal for Ford Vedette, Vendôme and Simca Vedette oil filter housing.Can be mounted on a cover or on a base depending on the model and year

fuel filter Big size ø 6 and 8 mm

Paper fuel filter for 6 or 8 mm hose.

fuel filter ø 6 and 8 mm

Paper fuel filter for 6 or 8 mm hose.

Fuel gauge - replacement float

Float in synthetic material resistant to current fuels. Used to replace the cork floats on the fuel gauge Length: 1.40" Diameter: 1.14"

Fuel gauge - replacement plastic float

White plastic float. Used to replace ring gauge floats.

Fuel hose diam 8 mm - by the meter

8 mm fuel hose sold by the meter.

Fuel pump - 6V or 12V control push button

6 or 12v 10A push button. Can be used to activate an electric fuel pump for a few seconds, for example.

Fuel pump - GUIOT diaphragm kit Ø90mm - Ford Vedette Simca

Replacement diaphragm for GUIOT fuel pump (Vedette Ford and Simca engine). Diam 90mm. Supplied with membrane and gaskets. (check the type of pump before ordering)

Gasket paste for motor - auto extrudable cartridge 200 ml

Mot. Silicone gasket & self-extruding housing RTV K164     high-quality, heat-resistant silicone     base: modified oxime silicone (acid-free hardening system)

Gauge Gasket cork 3 holes

Cork gasket for 3-hole fuel gauge

Gearbox or axle oil SAE 80-140 - IGOL - 1L

Viscosity index 80 - 140API GL-4(Not suitable for Peugeot type screw axles)

Head gasket solid copper 3 mm Ford Vendome Comete

Solid copper cylinder head gasket. Thickness 3mm. Used with very planed cylinder head. Mounts on Ford Vendôme, Comète, V8 21 and 22 hp.Tightening at 5m.kg. Installation with aerosol sealant is imperative.  

Ignition breakers RB (short) Ford Vedette Simca Versailles

A set of breakers for RB Ducellier igniter. Attention there are several RB versions - Please check your model according to the image. (Double igniters games require you to order 2 games.)

Ignition capacitor 6, 12 and 24V

6.12V and 24V compatible ignition capacitor.

Ignition coil 12v standard

Ignition coil guaranteed for use with a 12 V platinum screw igniter (breakers). Impedance respected to prevent the breakers from bluing.Works perfectly also with electronic module or integral electronic igniter. (Non contractual photo)

Ignition coil 12v VALEO

Ignition coil guaranteed for use with a 12 V platinum screw igniter (breakers). Impedance respected to prevent the breakers from bluing.Works perfectly also with electronic module or integral electronic igniter. (Non contractual photo)

Ignition coil 6V - High Performance

Bosch, NGK or Béru High Performance type ignition coil, guaranteed for use with:- 6 V platinum-plated screw igniter (breakers),- electronic ignition type 123 ignition,- platinum screw igniter + electronic amplification module

Ignition harness V8 Ford Vedette Simca Versailles Chambord

High performance ignition harness, black silicone, interference suppression in accordance with European legislation. Lengths specially adapted for Ford Vedette, Bee V8 engines; Vendôme, Comète, Monte Carlo and Simca Trianon, Versailles, Régence, ...

Ignition set 8 spark plugs V8 Ford Vedette Simca Versailles Chambord

Set of 8 NGK spark plugs for Ford Vedette, Comète, Vendôme, Monte Carlo and Simca Trianon, Versailles, Régence, Beaulieu, Chambord, Présidence, Marly 1 and 2 engines. Thermal index adapted to fuel Lead Free 95 and 98.

IGOL 20W50 mineral oil - 5L can

5 l can (non contractual photo) - Viscosity: 20W-50BenefitsHéRITAGE GTZ mineral oil.Multigrade lubricant for Gasoline and Diesel engines, made from severely refined mineral bases and additives suitable for older engines. The anti-wear additive ...

IGOL Rallye Gear axle transmission oil SAE 75 80 90 - GL4

Oil for gearbox and bridge for old mechanics. Type SAE 75 80 90 - GL4. 1L container.(Not suitable for Peugeot type screw axles)

IGOL semi-synthetic 15W50 oil - 5L can

Can of 5 L.Viscosity: 15W-50BenefitsHéRITAGE ZS semi-synthetic oil.Multigrade lubricant for gasoline engine of tourism, reinforced with synthetic bases, particularly adapted to the old engines, gasoline or diesel, equipped with an oil filter - ...

Kit 3 camshaft bushes x 3 - Ford Vedette

Kit 3 camshaft bushes x 3 - Ford Vedette 12hp engine

Kit of 12V electric fuel pump

" 12V electric fuel pump. Connects in series with the original fuel line. Keeps the hand pump. Avoids having to lift the hood to turn up gasoline before starting. To be powered through a push button for occasional operation. Low pressure, no need ...

Manometer Tachometer - 2 - 4 - 6 - 8 cyl - electric 12V - black background - for negative to mass

Mano "OS" Tachometer 0 to 5000 rpm for 4-cylinder petrol engine. Connects to the "break" terminal on the ignition coil. 52 mm recess on the pressure gauge side. delivered with lighting. for negative to ground

Manometer Tachometer - 2 - 4 - 6 - 8 cyl - electric 12V - ivory background - for negative to mass

Mano "OS" Tachometer 0 to 5000 rpm for 4-cylinder petrol engine. Connects to the "break" terminal on the ignition coil. 52 mm recess on the pressure gauge side. delivered with lighting. for negative to ground

Mechanism clutch 9L18 - Ford Vendome - Montecarlo

Clutch mechanism reconditioned, in standard exchange.Complete disassembly, micro balling, surfacing and retaring of the pressure plate.(The sending is done after receipt of the used mechanism, not destroyed - Depending on the year, ...

€530.40 TTC
(442,00 € HT)

Metal body battery switch - safety

Coupe batterie - permet d'isoler électriquement la batterie.

Pressure hose for igniter Ø 5.5 mm - by the meter

Hose to connect the igniter / carburetor depression 5.5 mm sold by the meter.

Regulateur électronique pour dynamo 6V positif à la masse - Ford Vedette - Simca Versailles

€191.00 TTC
(191,00 € HT)

Reinforced collar for exhaust - Ø 44-47 mm

Reinforced collar for exhaust - Ø 44-47 mmRobust French manufacturing

Reinforced collar for exhaust - Ø 52-55 mm

Reinforced collar for exhaust - Ø 52.55 mmRobust French manufacturing

Reinforced collar for exhaust - Ø 64-67 mm

Reinforced collar for exhaust - Ø 64-67 mmRobust French manufacturing

rubber fuel gauge seal - 3-hole

Rubber seal for 3-hole fuel gauge

Serflex collar for gasoline hose diam 8 mm

serflex collar 10-16 mm

Set of custom 4-groove piston rings Ford or Simca V8

Set of segments for V8 Ford Vedette, Vendôme, Simca Trianon, Versailles, Régence, Beaulieu, Chambord, Présidence, Marly 1 and 2, Ariane 8.For 4-groove piston, all dimensions, do not hesitate to contact us 033 4 42 57 79 06 for estimate.(Price ...

Set of piston rings 4 grooves Ø66.04 - 2x2x4x4 - Ford Vedette

Piston ring set Ø 66.04 - for Ford Vedette V8.For piston with 4 grooves, 2x2x4x4. Includes:- 16 compression segments 2 mm high- 16 scraper segments 4mm highNon contractual photo

Standard 6V coil ignition

Branded ignition coil guaranteed for use with 6 V platinum-plated igniter (breakers). Impedance respected to prevent the breakers from becoming blue. Also works perfectly with electronic module or integral electronic igniter.

sticker ford oil filter

Oil filter sticker. Mounts on Ford V8 Vedette, Vendôme, Comète, Monte Carlo etc.

Support de manomètre

Support métalique, laqué noir pour manomètre standard D52 mm. Prêt à fixé.

Temperature manometer with probe - black background

Mano "OS" temperature indicator (without electrical connection). Direct reading by probe mounted on a radiator hose (high outlet). 52 mm recess on the pressure gauge side.Capillary 1m80. Delivered with lighting and probe for the hose.

Temperature manometer with probe - ivory background

Mano "OS" temperature indicator (without electrical connection). Direct reading by probe mounted on a radiator hose (high outlet). 52 mm recess on the pressure gauge side.Capillary 1m80. Delivered with lighting and probe for the hose.

Universal bearing grease

For greasing bearings - Water resistant

V8 Ford Vedette Simca Versailles Chambord oil filter cartridge

Replacement cartridge for Ford Vedette, Vendôme and Simca Vedette oil filters. Identical to the C4 FRAM model. Info: Delivered without the gasket under the bell (or the cover for the Simca). It is for sale separately: click HERE