Exhaust gasket outlet manifold V8 Ford Vedette and Simca
" Exhaust gasket - at the manifold outlet - connection with" "Y" "2 in 1. 2 per engine - Sold individually. "
€9.60 TTC
(8,00 € HT)
(8,00 € HT)
Fuel pump - 6V or 12V control push button
6 or 12v 10A push button. Can be used to activate an electric fuel pump for a few seconds, for example.
€9.90 TTC
(8,25 € HT)
(8,25 € HT)
Oil pressure contact mano - Ford Vedette 1949 - 54
oil pressure switch for Ford Vedette engine from 1949 to 1954 - Thread M 10x100
€12.60 TTC
(10,50 € HT)
(10,50 € HT)
Set of 2 Ford Vedette front engine mounts
" Set of 2 front supports for V8 Ford Vedette. Fixing center distance to be slightly modified. "
€39.60 TTC
(33,00 € HT)
(33,00 € HT)
Central intake gasket - Ford Vedette
Central gasket intake housing for Vedette Ford. Special model for small Ford V8. Attention does not suit the V8 Simca Versailles -Chambord
€60.00 TTC
(50,00 € HT)
(50,00 € HT)
160 mm float fuel gauge - 6V
" Float fuel gauge. Adaptable model. Arm length approx. 160 mm. External diameter of plate 54 mm - fixing center distance 38 mm. Supplied with cork seal. 3-hole fixing. Internal resistance approx. 110 ohms. For 6-volt vehicle only. "
€48.00 TTC
(40,00 € HT)
(40,00 € HT)
Head ignition for RB Ducellier Ford starter Simca Versailles
Head for RB Ducellier distributor, distributor mounted on V8 Simca Versailles, Chambord etc. Can also be mounted on Marmon with petrol V8 equipped with civilian ignition.
€54.00 TTC
(45,00 € HT)
(45,00 € HT)
Ignition harness V8 Ford Vedette Simca Versailles Chambord
High performance ignition harness, black silicone, interference suppression in accordance with European legislation. Lengths specially adapted for Ford Vedette, Bee V8 engines; Vendôme, Comète, Monte Carlo and Simca Trianon, Versailles, Régence, ...
€83.95 TTC
(69,96 € HT)
(69,96 € HT)
Temperature manometer with probe - black background
Mano "OS" temperature indicator (without electrical connection). Direct reading by probe mounted on a radiator hose (high outlet). 52 mm recess on the pressure gauge side.Capillary 1m80. Delivered with lighting and probe for the hose.
€78.00 TTC
(65,00 € HT)
(65,00 € HT)
Ignition coil 12v standard
Ignition coil guaranteed for use with a 12 V platinum screw igniter (breakers). Impedance respected to prevent the breakers from bluing.Works perfectly also with electronic module or integral electronic igniter. (Non contractual photo)
€46.44 TTC
(38,70 € HT)
(38,70 € HT)
Aluminum water departure on engine block - Ford star
Aluminum water supply on engine block to radiator - Ford Vedette 1949 to 1954 and Comète 13 hpCareful French manufacturing - machined and welded aluminum.Two parts are needed per engine. Sold individually.
€91.80 TTC
(91,80 € HT)
(91,80 € HT)
Bearing 6203 - 17x40x12
Bearing - 17x40x12 waterproof (often used on dynamo, water pump, flywheel center, etc.). Check with the dimensions of your bearing.
€10.80 TTC
(9,00 € HT)
(9,00 € HT)
Clutch mechanism Ford Vedette
Clutch mechanism reconditioned, in standard exchange mounted on Ford Vedette, Abeille, Comète, Monte Carlo, Vendôme engine Complete disassembly, micro balling, surfacing and retaring of the pressure plate. (The sending is done after receipt ...
€315.00 TTC
(262,50 € HT)
(262,50 € HT)
Ford Vedette bearings - 030 - 52.54 mm
" Bearing set for Ford Vedette engine 1949 -54. (1 rear flange bearing + 2 front and central single bearings) Dimension: .030 US (0.75 mm) "
€810.00 TTC
(675,00 € HT)
(675,00 € HT)
Pinion oil pump mounted on axis - Ford Vedette
Replacement gear for oil pump - V8 Ford Vedette.Delivered riveted with new axle. (Advantageously replaces the celoron one that has become fragile over time)Attention for the V8 Simca 13 hp 2350 cm3, choose the reference "Simca oil pump pinion" on ...
€270.20 TTC
(270,20 € HT)
(270,20 € HT)
Exhaust suspension ring 63x96 width 27 mm - Peugeot 203
Suspension ring for Peugeot 203 exhaust and othersDimension approximately 63 x 96 x width 27 mm
€11.00 TTC
(11,00 € HT)
(11,00 € HT)
