Ford Vedette 54 disc clutch 215 mm
Clutch disc reconditioned, in standard exchange for Ford Vedette. Complete disassembly, micro balling and painting. (The sending is done after receipt of the used mechanism, not destroyed)(Depending on the year, non-contractual photo)
€144.00 TTC
(120,00 € HT)
(120,00 € HT)
6V electric fuel pump
6V electric fuel pump. To be connected to the ignition coil power supply. Connects in series with the original fuel line.Allows you to keep the manual pump. Avoids having to lift the hood to turn up gasoline before starting.Is intended to remain ...
€90.00 TTC
(75,00 € HT)
(75,00 € HT)
liner Ø 66.04 - semi finished 65.50 - Simca V8 Versailles Chambord
Liner Ø 66.04 - semi finished 65.50 - long 168mm Ø outside 69 mm Ø flange 70 mm height 5mm - Simca V8 Versailles Chambord - sold individually
€69.80 TTC
(58,17 € HT)
(58,17 € HT)
Clutch mechanism Ford Vedette
Clutch mechanism reconditioned, in standard exchange mounted on Ford Vedette, Abeille, Comète, Monte Carlo, Vendôme engine Complete disassembly, micro balling, surfacing and retaring of the pressure plate. (The sending is done after receipt ...
€354.00 TTC
(295,00 € HT)
(295,00 € HT)
Ignition capacitor 6, 12 and 24V
6.12V and 24V compatible ignition capacitor.
€14.40 TTC
(12,00 € HT)
(12,00 € HT)
Exhaust - stainless steel oval silencer - Ford Vedette
Stainless steel silencer for Ford Vedette.
€454.80 TTC
(379,00 € HT)
(379,00 € HT)
Exhaust - outlet tube + stainless steel stock - Ford Vedette
" Outlet tube with crosshead (bridge passage) to be connected to the silencer outlet. Ford Vedette 1949 to 1954. All stainless steel. "
€426.00 TTC
(355,00 € HT)
(355,00 € HT)
Ford Vedette and Simca Versailles Chambord braid set
" Set of braids for crankshaft Vedette Ford and Simca Aquilon engine (rear bearing and front bearing) Versailles, Chambord etc ... New product, of very high technical quality. Mounts with ease, cuts easily with a cuter leaving 1 to 2 mm ...
€49.90 TTC
(41,58 € HT)
(41,58 € HT)
Oil pressure contact mano - Ford Vedette 1949 - 54
oil pressure switch for Ford Vedette engine from 1949 to 1954 - Thread M 10x100
€12.60 TTC
(10,50 € HT)
(10,50 € HT)
- New
Ford Vedette gear lever retaining or repair ring -
This part fits around the gearshift lever. Its purpose is to protect the bowl that receives the lever base from breakage. Over time, the metal (Zamac) weakens and breaks. This ring also serves to repair the bowl when it begins to break.
€56.00 TTC
(56,00 € HT)
(56,00 € HT)
Ford Vedette bearings - 020 - 52.79 mm
" Bearing set for Ford Vedette engine 1949 -54. (1 rear flange bearing + 2 front and central single bearings) Dimension: .020 US (0.50 mm) "
€837.00 TTC
(697,50 € HT)
(697,50 € HT)
Ford Vedette cylinder head bolt set
Set of 34 hexagon head screws to replace the original studs - 3/8 16f / p unc 2 lengths of screws in the set - Allows easy removal of cylinder heads. Tightening 5 m.kg maximum
€155.20 TTC
(155,20 € HT)
(155,20 € HT)
Exhaust suspension ring 63x96 width 27 mm - Peugeot 203
Suspension ring for Peugeot 203 exhaust and othersDimension approximately 63 x 96 x width 27 mm
€11.00 TTC
(11,00 € HT)
(11,00 € HT)
Set of custom 4-groove piston rings Ford or Simca V8
Set of segments for V8 Ford Vedette, Vendôme, Simca Trianon, Versailles, Régence, Beaulieu, Chambord, Présidence, Marly 1 and 2, Ariane 8.For 4-groove piston, all dimensions, do not hesitate to contact us 033 4 42 57 79 06 for estimate.(Price ...
€336.00 TTC
(280,00 € HT)
(280,00 € HT)
Aviation collex type paste gasket for cylinder head - 450ml
Sealing paste to be applied on both sides of a cylinder head gasket. Product similar to "Collex". Leave to evaporate for about 30 min at room temperature after application, then fit the gasket - improves the seal - recommended with solid copper ...
€42.00 TTC
(35,00 € HT)
(35,00 € HT)
Central intake gasket - Ford Vedette
Central gasket intake housing for Vedette Ford. Special model for small Ford V8. Attention does not suit the V8 Simca Versailles -Chambord
€60.00 TTC
(50,00 € HT)
(50,00 € HT)
