Electronic regulator for 6V negative ground dynamo
Electronic regulator for 6V negative ground dynamo - Original appearance in ED3 housing.For dynamos with positive excitation.Charge stabilization at 7.4V. Brighter lighting, better battery charge quality, improved ignition voltage.(Exchange standard)
€208.00 TTC
(208,00 € HT)
(208,00 € HT)
Engine cover gasket for Ford Vedette
Engine gaskets kit (French manufacture) including:2 cylinder head gaskets with a copper face - thickness 1.6 mm1 gasket under central intake housing8 gaskets for exhaust manifold (6 block side - 2 at manifold outlet)1 oil filter foot gasket1 oil ...
€330.00 TTC
(275,00 € HT)
(275,00 € HT)
Pellet set of 4 - Ford Vedette and Simca engine block
Set of 4 pellets for Vedette Ford and Simca engine block diam. about 44 mm.
€44.00 TTC
(44,00 € HT)
(44,00 € HT)
Exhaust support strap reinforces 90 mm
Suspension strap for exhaust. Robust construction, reinforced rubber, metal eyelets.92 mm center distance for M8 mm screws.
€13.48 TTC
(13,48 € HT)
(13,48 € HT)
Ford Vedette bearings - 030 - 52.54 mm
" Bearing set for Ford Vedette engine 1949 -54. (1 rear flange bearing + 2 front and central single bearings) Dimension: .030 US (0.75 mm) "
€810.00 TTC
(675,00 € HT)
(675,00 € HT)
Fuel gauge - replacement float
Float in synthetic material resistant to current fuels. Used to replace the cork floats on the fuel gauge Length: 1.40" Diameter: 1.14"
€17.72 TTC
(17,72 € HT)
(17,72 € HT)
Rod bearings Ford Vedette 53-54 or Simca Chambord - 010 - 44.34 mm
" Set of bearings (16 half-shells) for Ford Vedette 2nd generation 1953-54 and Simca V8 engines. Dimension: .010 US (0.25 mm) Each connecting rod receives its pair of bearings. "
€504.00 TTC
(420,00 € HT)
(420,00 € HT)
Set of 8 pistons 66.04 Ford Vedette
Set of 8 pistons - New manufacture, similar to the original model - reduction in piston mass (approximately 255 gr with rings) - molybdenum treatment - cylinder dimension 66.04 mm. Supplied with segments, pins and circlips - The segments supplied ...
€1,548.00 TTC
(1 290,00 € HT)
(1 290,00 € HT)
Rod bearings Ford Vedette 53-54 or Simca Chambord - 040 - 43.57 mm
" Set of bearings (16 half-shells) for Ford Vedette 2nd generation 1953-54 and Simca V8 engines. Dimension: .040 US (1 mm) Each connecting rod receives its pair of bearings. "
€741.60 TTC
(618,00 € HT)
(618,00 € HT)
Rod bearings Ford Vedette 53-54 or Simca Chambord - 020 - 44.08 mm
" Set of bearings (16 half-shells) for Ford Vedette 2nd generation 1953-54 and Simca V8 engines. Dimension: .020 US (0.50 mm) Each connecting rod receives its pair of bearings. "
€504.00 TTC
(420,00 € HT)
(420,00 € HT)
Clutch mechanism Ford Vedette
Clutch mechanism reconditioned, in standard exchange mounted on Ford Vedette, Abeille, Comète, Monte Carlo, Vendôme engine Complete disassembly, micro balling, surfacing and retaring of the pressure plate. (The sending is done after receipt ...
€354.00 TTC
(295,00 € HT)
(295,00 € HT)
Oil filter foot gasket Ford Vedette Simca
Gasket to be placed between the central crankcase and the base of the oil filter. "Y" shaped.
€16.40 TTC
(16,40 € HT)
(16,40 € HT)
IGOL Rallye Gear axle transmission oil SAE 75 80 90 - GL4
Oil for gearbox and bridge for old mechanics. Type SAE 75 80 90 - GL4. 1L container.(Not suitable for Peugeot type screw axles)
€18.00 TTC
(15,00 € HT)
(15,00 € HT)
Water pump repair kit with aluminum impeller - Ford Vedette
Repair kit for water pump for "Y" or "T" pump body - years 1949-54. New axle is 16mm instead of 12 mm. So you need to drill body 16.5 mm. We recommend correcting the seat of the rotating joint at the back of the body.
€151.20 TTC
(151,20 € HT)
(151,20 € HT)
