12V electric fuel pump

" 12V electric fuel pump. Connects in series with the original fuel line. Keeps the hand pump. Avoids having to lift the hood to turn up gasoline before starting. To be powered through a push button for occasional operation. Low pressure, no need ...

12v to 6v regulator for temperature, pressure, fuel gauge

This module allows the use of 6V pressure gauges on a 12V vehicle (negative to ground). Mounts on a temperature gauge, pressure, fuel gauge, ...Very practical, it is fixed directly on the supply terminal of the pressure gauge thanks to a hole ...

2-wire fuel gauge - Peugeot 403

2-wire fuel gauge - Peugeot 403 Meticulous manufacturing

80 mm FLAT piston liners set - Peugeot 403 - D4 - 8cv

Set of 4 liners + 4 complete FLAT pistons (segments, clips, axles) for Peugeot 403 (8cv). The manufacture of the pistons and the choice of segmentation are guaranteed of quality.New product. Original STD dimension, bore 80 mm.

Aerosol gasket for cylinder head

Sealing spray varnish to be sprayed on both sides of a cylinder head gasket. Improves sealing, essential with solid copper gaskets (any thickness)

Aviation collex type paste gasket for cylinder head - 117ml

Sealing paste to be applied on both sides of a cylinder head gasket. Product similar to "Collex". Leave to evaporate for about 30 min at room temperature after application, then fit the gasket - improves the seal - recommended with solid copper ...

Aviation collex type paste gasket for cylinder head - 450ml

Sealing paste to be applied on both sides of a cylinder head gasket. Product similar to "Collex". Leave to evaporate for about 30 min at room temperature after application, then fit the gasket - improves the seal - recommended with solid copper ...

Axe 8 mm avec papillon pour réparation carburateur Solex 32 PBIC ou similaire

Axle 8.5 mm Ø repair - without butterfly - Solex 32 PBIC or similarsimilar

Shaft dimension repair 8.5 mm without butterfly for repair carburettor Solex 32 PBIC or similarOverall length 91.5 mm

Battery switch - safety

Battery isolator - used to electrically isolate the battery. To be placed on a terminal of the battery.

Battery switch with key - security

Battery switch with key - security

Bearing 6203 - 17x40x12

Bearing - 17x40x12 waterproof (often used on dynamo, water pump, flywheel center, etc.). Check with the dimensions of your bearing.

Bearing clutch Peugeot 203 - 403 - D3 - D4

Graphite stop for clutch mechanism.

Bearing set - Peugeot 203 - 403 0.30

Set of 3 bearings for Peugeot 203 and 403.Repair dimension 0.30.

Bearing set - Peugeot 203 - 403 0.50

Set of 3 bearings for Peugeot 203 and 403.Repair dimension 0.50.

Bearing set - Peugeot 203 - 403 STD side

Set of 3 bearings for Peugeot 203 and 403.Original standard dimension

Belt Peugeot 203 and 403 (petrol)

Belt width 17mm

Brushes or carbon for Peugeot 203 403 disengageable water pump

Contact with brushes (carbon) for Peugeot 203 403 disengageable water pump. Delivered with the wire.

Calibrouge (Plastigage) mechanical clearance measurement

"Plastigage"The Calibrouge ("plastigage or plastigauge") is a simple and practical tool for measuring the clearances of your bearings. Range of use: operating clearance from 0.025 to 0.175 mm

Carburetor 32 PBICA - Peugeot 403 and 404

Carburateur neuf type Solex 32 PBICA. Se monte sur Peugeot 403  404. Selon modèle ajuster gicleurs, buse et réglages  

Carburetor 34 PBICA - Peugeot 403 and 404 504

Carburateur neuf type Solex 34 PBICA. Se monte sur Peugeot 403  404 504. Selon modèle ajuster gicleurs, buse et réglages  

Charger and maintenance 6v / 12v Accumate

AccuMate is designed to automatically charge and monitor batteries without the danger of overcharging them, regardless of plug-in time. AccuMate is available for all 6V and 12V lead acid batteries, making it a perfect accessory for owners of ...

Complete set of solex 32 pbic carburetor gaskets

Solex 32 pbic carburetor gaskets kit - accelerator pump diaphragm included (Colorale, Goélette, R2087, Frigate, etc) Version with manual starter

Connecting rod bearings set - Peugeot 203 - 403 dimension 0.30

Set of bearings for 4 Peugeot 203 and 403 connecting rods.Repair dimension 0.30. French made.

Connecting rod bearings set - Peugeot 203 - 403 dimension 0.50

Set of bearings for 4 Peugeot 203 and 403 connecting rods.Repair dimension 0.50. French made.

Connecting rod bearings set - Peugeot 203 - 403 standard dimension

Set of bearings for 4 Peugeot 203 and 403 connecting rods. Standard original dimension. French manufacture.

Crankshaft plugs - set of 4 - Peugeot 203 403

Set of 4 20x15 plugs for Peugeot 203/403 crankshaft

Dark green engine paint RAL 6005 - 500 ml

Dark green engine paint RAL 6005 -Pot of 500 mlSuitable for engines, housings, gearboxes, differentials, brake drums and all parts subject to heating in cast iron, steel and light alloys.Direct application on degreased metal (or better, treated ...

€40.80 TTC
(34,00 € HT)

Disc clutch Peugeot 203 403

Reconditioned clutch disc, in standard exchange for Peugeot 203 403. Complete disassembly, micro balling and painting. (The sending is done after receipt of the used mechanism, not destroyed) (Depending on the year, non-contractual photo)

€103.20 TTC
(86,00 € HT)

Distribution chain 64 links Peugeot 203 and 403

Timing chain for Peugeot 203,403 engine and derivatives - 64 links (for model with tensioner)

Double pressure gauge holder

Metal support, black lacquered for standard manometer D52 mm. Ready to fix.

Echappement sangle support renforcé 50 mm

Sangle de suspension pour échappement, caoutchouc armé. entraxe 52 mm pour vis M8 mm.

Electronic ignition amplifier assistance module - 12V negative to earth

Electronic ignition assistance module. Allows for more energetic spark plug ignition, improved starting, smoother pick-up, helps reduce fuel consumption and consequently pollution.The breakers (platinum-plated screws) are left in place - the ...

Engine paint black RAL 9005 - 500 ml

Black paint - 500 ml jarSuitable for engines, housings, gearboxes, differentials, brake drums and all parts subject to heating in cast iron, steel and light alloys.Direct application on degreased metal (or better, treated with our Phosprim 4090), ...

€40.80 TTC
(34,00 € HT)

Engine paint oxide green RAL 6020 - 500 ml

Engine paint oxide green RAL 6020 -Pot of 500 mlSuitable for engines, housings, gearboxes, differentials, brake drums and all parts subject to heating in cast iron, steel and light alloys.Direct application on degreased metal (or better, treated ...

€40.80 TTC
(34,00 € HT)

Engine red paint - 500 ml -

Engine red paint -Pot of 500 mlSuitable for engines, housings, gearboxes, differentials, brake drums and all parts subject to heating in cast iron, steel and light alloys.Direct application on degreased metal (or better, treated with our Phosprim ...

€40.80 TTC
(34,00 € HT)

Exhaust manifold paint - 250 ml

€48.00 TTC
(40,00 € HT)

Exhaust support strap reinforces 90 mm

Suspension strap for exhaust. Robust construction, reinforced rubber, metal eyelets.92 mm center distance for M8 mm screws.

Exhaust suspension ring 63x96 width 27 mm - Peugeot 203

Suspension ring for Peugeot 203 exhaust and othersDimension approximately 63 x 96 x width 27 mm

Ford RAL 5005 blue engine paint - 500 ml

Ford RAL 5005 blue engine paint - 500 ml jarSuitable for engines, housings, gearboxes, differentials, brake drums and all parts subject to heating in cast iron, steel and light alloys.Direct application on degreased metal (or better, treated with ...

€40.80 TTC
(34,00 € HT)

fuel filter Big size ø 6 and 8 mm

Paper fuel filter for 6 or 8 mm hose.

fuel filter ø 6 and 8 mm

Paper fuel filter for 6 or 8 mm hose.

Fuel gauge - replacement float

Float in synthetic material resistant to current fuels. Used to replace the cork floats on the fuel gauge Length: 1.40" Diameter: 1.14"

Fuel gauge - replacement plastic float

White plastic float. Used to replace ring gauge floats.

Fuel hose diam 8 mm - by the meter

8 mm fuel hose sold by the meter.

Fuel needle - Solex 32 PBIC carburettor or similar

Fuel needle - Solex 32 PBIC carburettor or similar

Fuel pump repair kit 4291 - Peugeot 203 403 D3 D4

Fuel pump repair kit ref 4291 for Peugeot 203, 403, utility D3, D4 and derivatives.Also suitable for pumps ref. 3291,3292, 3320, 3397 and 4292.

Fuel pump with lever Peugeot 203/403

Fuel pump with Peugeot 203, 403, utility D3, D4 and derivatives. Supplied with base gasket.

gasket for solex 32 pbic carburetor

2 x paper gaskets for Solex 32 pbi carburetor base.Fixing center distance: 60 mmCentral passage: 32 mmTotal length: 78 mmwidth: 50mm

Gasket paste for motor - auto extrudable cartridge 200 ml

Mot. Silicone gasket & self-extruding housing RTV K164     high-quality, heat-resistant silicone     base: modified oxime silicone (acid-free hardening system)

Gauge Gasket cork 3 holes

Cork gasket for 3-hole fuel gauge

Gearbox or axle oil SAE 80-140 - IGOL - 1L

Viscosity index 80 - 140API GL-4(Not suitable for Peugeot type screw axles)

Ignition - complete igniter with vacuum - M48

Complete igniter with vacuum capsule AND centrifugal advance - similar curve Ducellier M48 - maximum advance 12 ° on igniter - delivered tested and greased. Dimensions :- length between shoulder (stop under the body) and end of trainer: 64mm- ...

Ignition - Electronic ignition for Peugeot 203/403 / D3 / D4

123 Ignition electronic ignition for Peugeot 203, 204, 304, 403, D3, D4, 404, 504, 505, J5, J7, J9Replaces S.E.V. Marchal and Ducellier M3, M12, XC1, M127, M59, M43, M75, M48, M36, M42, M50, M53, M77, M78, M95, M71, M86 & M130Installs in ...

Ignition capacitor 6, 12 and 24V

6.12V and 24V compatible ignition capacitor.

Ignition coil 12v standard

Ignition coil guaranteed for use with a 12 V platinum screw igniter (breakers). Impedance respected to prevent the breakers from bluing.Works perfectly also with electronic module or integral electronic igniter. (Non contractual photo)

Ignition coil 12v VALEO

Ignition coil guaranteed for use with a 12 V platinum screw igniter (breakers). Impedance respected to prevent the breakers from bluing.Works perfectly also with electronic module or integral electronic igniter. (Non contractual photo)

Ignition finger igniter Ducellier 65mm

Finger for Ducellier distributor equipped with a 65mm headMounts with Ducellier 65 mm head

Ignition head Ducellier 65 mm

Head for Ducellier distributor: Interlocking inside the head = 65 mm, outside about 72 mm.To be assembled with breakers 1 237 013 808, and ducellier finger.

Ignition protected harness Peugeot 203 - 403 petrol

Ignition harness for Peugeot 203/403 petrol engine.Current quality manufacture in red silicone.

Ignition set of Ducellier breakers

Set of breakers for Ducellier distributor For Renault Prairie, R2087, Goélette and derivatives

Ignition set of SEV breakers

" Set of breakers for SEV igniter For Renault Prairie, R2087, Goélette and derivatives "

IGOL 20W50 mineral oil - 5L can

5 l can (non contractual photo) - Viscosity: 20W-50BenefitsHéRITAGE GTZ mineral oil.Multigrade lubricant for Gasoline and Diesel engines, made from severely refined mineral bases and additives suitable for older engines. The anti-wear additive ...

IGOL Oil for screw bridge and bronze crown - 2 liters - Peugeot 203 403 404

Special lubricant for rear axle and worm reducers. Has excellent pressure resistance properties, a very high viscosity index and good protection against oxidation and corrosion.     Miscible with castor-based oils, and with extreme pressure oils. ...

IGOL semi-synthetic 15W50 oil - 5L can

Can of 5 L.Viscosity: 15W-50BenefitsHéRITAGE ZS semi-synthetic oil.Multigrade lubricant for gasoline engine of tourism, reinforced with synthetic bases, particularly adapted to the old engines, gasoline or diesel, equipped with an oil filter - ...

Kit of 12V electric fuel pump

" 12V electric fuel pump. Connects in series with the original fuel line. Keeps the hand pump. Avoids having to lift the hood to turn up gasoline before starting. To be powered through a push button for occasional operation. Low pressure, no need ...

Manometer Tachometer - 2 - 4 - 6 - 8 cyl - electric 12V - black background - for negative to mass

Mano "OS" Tachometer 0 to 5000 rpm for 4-cylinder petrol engine. Connects to the "break" terminal on the ignition coil. 52 mm recess on the pressure gauge side. delivered with lighting. for negative to ground

Manometer Tachometer - 2 - 4 - 6 - 8 cyl - electric 12V - ivory background - for negative to mass

Mano "OS" Tachometer 0 to 5000 rpm for 4-cylinder petrol engine. Connects to the "break" terminal on the ignition coil. 52 mm recess on the pressure gauge side. delivered with lighting. for negative to ground

Metal body battery switch - safety

Coupe batterie - permet d'isoler électriquement la batterie.

paper gasket x 2 + thermal wedge for solex 32 pbic carburetor

kit 2 joints papier + cale thermique pour embase de carburateur Solex 32 pbi.  

Peugeot 203 403 clutch mechanism

Clutch mechanism reconditioned, in standard exchange. Fitted on Peugeot 203, 403, D4A, etc ...Complete disassembly, micro-blasting, surfacing and retaring of the pressure plate.(The shipment is made after receipt of the used mechanism, not ...

€282.00 TTC
(235,00 € HT)

Peugeot 203 air filter

Paper cartridge for Peugeot 203 air filter. Conforms to original dimensions.Diam 140/150 mm - height 60/65 mm - central hole 90 mm approximately

Peugeot 203-403 oil filter cartridge

Cartridge for Peugeot 203-403 petrol oil filter

Peugeot 403 air filter hose

Air filter - carburetor connection hose

Peugeot 403 engine gaskets kit - 7 hp

Engine gaskets set Peugeot 403 - 7 HP . Bore 75 mm Cylinder head gasket included.

Peugeot 403 engine gaskets kit - 8 hp

Engine gaskets kit for Peugeot 403 - 8 hp - 80 mm boreHead gasket and base gaskets included.

Peugeot accelerator cable403 (kit)

Kit for repairing the accelerator cable Peugeot 403 all models.

Pressure hose for igniter Ø 5.5 mm - by the meter

Hose to connect the igniter / carburetor depression 5.5 mm sold by the meter.

Reinforced collar for exhaust - Ø 44-47 mm

Reinforced collar for exhaust - Ø 44-47 mmRobust French manufacturing

Reinforced collar for exhaust - Ø 52-55 mm

Reinforced collar for exhaust - Ø 52.55 mmRobust French manufacturing

Reinforced collar for exhaust - Ø 64-67 mm

Reinforced collar for exhaust - Ø 64-67 mmRobust French manufacturing

rubber fuel gauge seal - 3-hole

Rubber seal for 3-hole fuel gauge

Sandblasting tablet 52 mm pump side Peugeot 203 403

1 pellet diam. 52mm on cylinder head, behind water pump

Sandblasting tablets x 2 - 60 mm cylinder head Peugeot 203 403

Set of 2 pellets diam. 60mm on cylinder head for Peugeot 203-403

Sedis belt injection pump 404 and 504 Peugeot

Sedis 404 and 504 Peugeot injection pump belt. High quality manufacturing.

Segment set Ø 80 mm Peugeot 403 - 2cx2x4.5x4.5

Segment set Ø 80 mm Peugeot 403 - 2cx2x4.5x4.5

Serflex collar for gasoline hose diam 8 mm

serflex collar 10-16 mm

Set 4 cylinder seals - Peugeot 203 403 8cv - 80mm

Set 4 cylinder seals - Peugeot 203 403 8cv - 80mm

€19.90 TTC
(16,58 € HT)

Set of 2 Peugeot 403 engine mounts

Set of 2 front brackets for Peugeot 403. 86 mm fixing center distance (engine block with 3 reinforcements).

Set of 4 Peugeot 203-403 spark plugs

Set of 4 NGK spark plugs for Peugeot 23 and 403 petrol enginesCompatible with SP 95 or Sp 98 fuel

Set of 75 mm bomb pistons/ liners - Peugeot 203 - 403 - 7cv

" Set of 4 liners + 4 complete domed pistons (segments, clips, axles) for Peugeot 203 or 403 (7cv). New product. STD original dimension, bore 75 mm. Non-contractual photo "

SEV finger ignition large model

Finger for SEV igniter (large model)

Shaft 8.5 mm Ø repair - repair Solex 32 PBIC carburettor or similar

Shaft dimension repair 8.5 mm with butterfly for repair carburettor Solex 32 PBIC or similarOverall length 91.5 mm

Support de manomètre

Support métalique, laqué noir pour manomètre standard D52 mm. Prêt à fixé.

Temperature manometer with probe - black background

Mano "OS" temperature indicator (without electrical connection). Direct reading by probe mounted on a radiator hose (high outlet). 52 mm recess on the pressure gauge side.Capillary 1m80. Delivered with lighting and probe for the hose.

Temperature manometer with probe - ivory background

Mano "OS" temperature indicator (without electrical connection). Direct reading by probe mounted on a radiator hose (high outlet). 52 mm recess on the pressure gauge side.Capillary 1m80. Delivered with lighting and probe for the hose.

Universal bearing grease

For greasing bearings - Water resistant

UX 35 brush set

Set of 2 brushes or carbon brushes for 6 / 12v DUCELLIER dynamos Ref 75262 - 18444Composition of the set: 1 broom U35 and 1 broom U 22CCorrespondence: Le Carbone-Lorraine - Ava: UX 35 - 18444 / Sebs: 31Assembly on Dynamos Ducellier n °: 7131 A / ...

Valve guide x4 - + 0.05 MM - 8.5x14.11x56.50 - Peugeot 203 - 403

Set of 4 cast iron inlet and exhaust valve guides: outer bore repair dimension + 0.6 = Ø 14.11 - 8.5x14.11x56.50Peugeot 203 and 403, 1290cm³ TM4 TMP4 D4A engines, inner diameter 8.5mm, diam. ext. 14.05mm, length 55.4mm.(8 guides per cylinder head)

Valve guide x4 - +0.10 MM - 8.5x14.16x56.50 - Peugeot 203 - 403

Set of 4 cast iron intake and exhaust valve guides: outer bore repair dimension + 0.11 = Ø 14.16 - 8.5x14.11x56.50Peugeot 203 and 403, 1290cm³ TM4 TMP4 D4A engines, inner diameter 8.5mm, diam. ext. 14.05mm, length 55.4mm.(8 guides per cylinder head)

Valve guide x4 - original - 8.5x14.05x56.50 - Peugeot 203 - 403

Set of 4 valve guides adm. and cast iron scale: original outside bore Ø 14.05 - 8.5x14.05x56.50Peugeot 203 and 403, 1290cm³ TM4 TMP4 D4A engines, diam. int. 8.5mm, diam. ext. 14.05mm, length 55.4mm.(8 guides per cylinder head)

Valves x 4 - ADM Ø 35x8.5x116.4 - Peugeot 203

Valves x 4 - ADM Ø 35x8.5x116.4 - Peugeot 203

Valves x 4 - ADM Ø 37x8.5x116.4 - Peugeot 203 - 403

Set of 4 ADM valves Ø 37x8.5x116.4 - Peugeot 203 - 403

Valves x 4 - ECH Ø 32.5x8.5x115.9 - Peugeot 203 - 403

Valves x 4 - ECH Ø 32.5x8.5x115.9 - Peugeot 203 - 403