Pair of Ford Vedette front shocks
Set of 2 front shock absorbers for Ford Vedette all models.Record brand, 100% conforms to the original assembly.Sold in pairs.
€287.16 TTC
(239,30 € HT)
(239,30 € HT)
Tie rod ends - Ford Vedette
Set of steering ball joints for Ford Vedette 1949 to 54, Abeille, Vendôme, Comète, Monte Carlo.Includes:- 1 x long ball joint,- 1 x short ball joint.(the adjusting sleeve is not supplied)
€176.00 TTC
(176,00 € HT)
(176,00 € HT)
Upper and lower adjustment for Ford vedette front hub
Allows adjustment of the camber on the front axle. When these parts are worn, play appears making it impossible to adjust the geometry of the front axle and making the vehicle's driving imprecise.Sold individually (2 per front hub)
€96.00 TTC
(96,00 € HT)
(96,00 € HT)
Set of 2 Ford Vedette pivots 1949-52
Set of 2 pivots (in standard exchange), ready to install. The set includes 1 pivot G + 1 pivot D, new bronze bushings, treated steel pivot pins, rectified axis line.Mounts on:- Ford Vedette from 1949 to 52- some Vedette 1953- Comète 13 and 22cv, ...
€426.20 TTC
(426,20 € HT)
(426,20 € HT)
Ford Vedette stabilizer bar support
Mounting bracket for stabilizer bar. 2 per vehicle - Sold individually.
€31.80 TTC
(26,50 € HT)
(26,50 € HT)
Kit 2 x Ford Vedette pivots
" Ford Vedette front pivot repair kit for all models, Bee, Comet, Monte Carlo, Vendôme. Includes 2 pins and 4 bronze bushings. (for 2 wheels). The 2 axes are in treated steel for a much greater hardness than ordinary commercial products. ...
€240.00 TTC
(240,00 € HT)
(240,00 € HT)
Rubber bush kit - silentblocs for Ford Vedette front axle
Kit including dust covers and other grease covers to remake the front axle, including those for the stabilizer bar. The set includes:4 x ring (ref Ford 3193)4 x steering ball joint grease cover4 x grease cover on upper triangle axle - chassis ...
€556.20 TTC
(463,50 € HT)
(463,50 € HT)
Ford Vedette gearbox outlet seal ring
Sealing ring (oil seal) placed at the Ford Vedette gearbox outlet.
€17.00 TTC
(14,17 € HT)
(14,17 € HT)
Set of 2 pivot 1953-54 Ford Vedette Comete Vendome
Set of 2 pivots (in standard exchange), ready to install. The set includes 1 pivot G + 1 pivot D, new bronze bushings, treated steel pivot pins, rectified axis line.Mounts on- Ford Vedette 1954- some Vedette 1953Another reference is available for ...
€426.20 TTC
(426,20 € HT)
(426,20 € HT)
Ford Vedette gearbox inlet seal ring
Sealing ring (oil seal) placed at the Ford Vedette gearbox outlet.35 x 51
€17.00 TTC
(14,17 € HT)
(14,17 € HT)
Front hub kit - Ford Vedette - Vendome
Front wheel hub kit. Includes:- 1 internal conical bearing- 1 external conical bearingThe set is valid for one front wheel.
€129.60 TTC
(108,00 € HT)
(108,00 € HT)
Steering relay - Ford vedette - Vendôme - Comet
Steering relay attached to the passenger side chassis. Remember to replace the tie rod with the 2 rotation nuts to remove wear clearances.
€236.00 TTC
(236,00 € HT)
(236,00 € HT)
Grease cover on upper triangle wheel side - Ford Vedette
Protection mounted on the upper arm on the wheel pivot side - Ford reference - 3075 - 4 per vehicle - Sold individually.
€20.40 TTC
(17,00 € HT)
(17,00 € HT)
160 mm float fuel gauge - 6V
" Float fuel gauge. Adaptable model. Arm length approx. 160 mm. External diameter of plate 54 mm - fixing center distance 38 mm. Supplied with cork seal. 3-hole fixing. Internal resistance approx. 110 ohms. For 6-volt vehicle only. "
€48.00 TTC
(40,00 € HT)
(40,00 € HT)
Viewed products
Boot handle sole kit - Ford Vedette 1954 - Berline / Coupé / Cabriolet
Sole kit for trunk handle Ford Vedette 1954 - Berline / Coupé / Cabriolet - Neat French manufacturing - Techni-Tacot exclusivityUnderstand :1 x rear trunk handle sole
€26.58 TTC
(26,58 € HT)
(26,58 € HT)
Rear brake cylinder -25.4 mm - cone protruding - Peugeot D4 - 04/64 to 05/65
Rear wheel cylinder d 25.4mm, Peugeot D4 D4A D4B - 04/64 to 05/65.Model with cone coming out of the liquid inlet well. Non contractual photo.
€60.60 TTC
(50,50 € HT)
(50,50 € HT)
Seals of the 2 rear doors - Peugeot D3 D4
Seals of the 2 rear doors - Peugeot D3 D4.Product sold in one length. To be cut according to the length of each door.
€117.60 TTC
(98,00 € HT)
(98,00 € HT)
copy of Segment set Ø 66.80 mm Simca Chambord 2.38x2.38x5 - 8cyl
Segment set Ø 66.80 mm Simca 2.38x2.38x5 - 8cyl
€297.60 TTC
(248,00 € HT)
(248,00 € HT)
Pressure hose for igniter Ø 5.5 mm - by the meter
Hose to connect the igniter / carburetor depression 5.5 mm sold by the meter.
€10.20 TTC
(8,50 € HT)
(8,50 € HT)
Front brake hose 493 mm Peugeot D4 - 11/57 to end
Front brake hose length 493 mm for Peugeot D4 D4A D4B - please check the correspondence with your model before ordering.For other models, please call us
€42.00 TTC
(35,00 € HT)
(35,00 € HT)
Rear brake cylinder -22 mm - cone protruding - Peugeot D4 - 11/57 a 04/64
Rear brake cylinder -22 mm - protruding cone - Peugeot D4 - 11/57 to 04/64 - French manufacture.
€70.80 TTC
(59,00 € HT)
(59,00 € HT)
