Grease cover on lower triangle wheel side - Ford Vedette

Rubber ring for Ford Vedette front axle - on lower pivot - 4 per vehicle - Sold individually Ford Ref = 3193

160 mm float fuel gauge - 6V

" Float fuel gauge. Adaptable model. Arm length approx. 160 mm. External diameter of plate 54 mm - fixing center distance 38 mm. Supplied with cork seal. 3-hole fixing. Internal resistance approx. 110 ohms. For 6-volt vehicle only. "

Grease cover on upper triangle frame side - Ford Vedette

Rubber protection mounted on upper triangle - Ford reference (3196) - 4 per vehicle - Sold individually.

Spinnaker ring on 1/2 rear shaft - Ford Vedette - Comete

Spinnaker ring on 1/2 rear shaft - Ford Vedette - Comete(to be mounted on the left and right side)

Etoquiau - central blade fixing - Ford Vedette Vendome Comete monte Carlo

Tie rod ends - Ford Vedette

Set of steering ball joints for Ford Vedette 1949 to 54, Abeille, Vendôme, Comète, Monte Carlo.Includes:- 1 x long ball joint,- 1 x short ball joint.(the adjusting sleeve is not supplied)

Ford Vedette stabilizer bar bush

Silent block for Ford Vedette stabilizer bar - 4 per side or 8 for a vehicle - Sold individually.

Ford Vedette gearbox inlet seal ring

Sealing ring (oil seal) placed at the Ford Vedette gearbox outlet.35 x 51

Ford Vedette rear suspension blade bush

" Silent block to be mounted in the eyelets of the rear suspension blades - 6 pieces per suspension (or 12 on a vehicle) - Sold individually D int = 12 mm D ext = 20.5 mm approximately D ext with collar = 30 mm Long without collar = 22 mm "

Grease cover on upper triangle wheel side - Ford Vedette

Protection mounted on the upper arm on the wheel pivot side - Ford reference - 3075 - 4 per vehicle - Sold individually.

Set of 2 pivot 1953-54 Ford Vedette Comete Vendome

Set of 2 pivots (in standard exchange), ready to install. The set includes 1 pivot G + 1 pivot D, new bronze bushings, treated steel pivot pins, rectified axis line.Mounts on- Ford Vedette 1954- some Vedette 1953Another reference is available for ...

Set of 2 Ford Vedette pivots 1949-52

Set of 2 pivots (in standard exchange), ready to install. The set includes 1 pivot G + 1 pivot D, new bronze bushings, treated steel pivot pins, rectified axis line.Mounts on:- Ford Vedette from 1949 to 52- some Vedette 1953- Comète 13 and 22cv, ...

Rubber bush kit - silentblocs for Ford Vedette front axle

Kit including dust covers and other grease covers to remake the front axle, including those for the stabilizer bar. The set includes:4 x ring (ref Ford 3193)4 x steering ball joint grease cover4 x grease cover on upper triangle axle - chassis ...

Upper and lower adjustment for Ford vedette front hub

Allows adjustment of the camber on the front axle. When these parts are worn, play appears making it impossible to adjust the geometry of the front axle and making the vehicle's driving imprecise.Sold individually (2 per front hub)

Ring x 2 - gearbox lever or column foot - Ford Vedette and derivatives

Set of 2 repair rings to replace the silent blocks of the gearbox levers or those at the bottom of the column - Ford Vedette and derivatives.Requires 2 sets per vehicle

IGOL Rallye Gear axle transmission oil SAE 75 80 90 - GL4

Oil for gearbox and bridge for old mechanics. Type SAE 75 80 90 - GL4. 1L container.(Not suitable for Peugeot type screw axles)