Set of 4 relined brake shoes Panhard Dyna x86
Set of 4 relined brake shoes (front or rear) 195 mm x 30 mm in standard exchange for Panhard Dyna X86, Dyna Z, PL 17 and series 24Microblasting, varnish, industrial bonding of friction. Strong adhesion.Eliminates the problem of rivets that could ...
€138.00 TTC
(115,00 € HT)
(115,00 € HT)
Brake line - from 150 to 200 cm
Brake line re-manufactured on request, only in copper diameter 6.35 mm. Provide model (length and 2 original end pieces)Shipping after receiving your model.
€69.24 TTC
(57,70 € HT)
(57,70 € HT)
Rear brake cylinder 19mm - 3/8 Panhard 24 - 07/1964 to end
Rear wheel cylinder 19mm - Panhard 24 équipé frein à tambours - 07/1964 à fin de série
€69.12 TTC
(57,60 € HT)
(57,60 € HT)
FRONT RIGHT 28.5mm brake cylinder - Panhard PL 17 - 60 to 62
Front wheel cylinder L PL17 from 1960 to March 62 - d 28.57 mm. Entry 3/8 - Right mounting. Length 72 mm - inside liquid passage = 8.5 mm
€84.00 TTC
(70,00 € HT)
(70,00 € HT)
Cylindre frein arrière 22 mm - Panhard Dyna Z - montage RECORD
Rear L and R brake cylinder Panhard Dyna - Diam 22mm - RECORD.Sold individually (1 cylinder per wheel)
€76.80 TTC
(64,00 € HT)
(64,00 € HT)
Brake line - from 200 to 250 cm
Brake line remanufactured on request, only in copper diameter 6.35 mm. Provide model (length and 2 original tips)Shipping after receipt of your model.
€76.44 TTC
(63,70 € HT)
(63,70 € HT)
Metal insert tip for jar
Metal fitting to be fitted with the brake reservoir rubber to prevent the tearing and accidental draining of the brake fluid reservoir.
€10.80 TTC
(9,00 € HT)
(9,00 € HT)
Pipe Ø 8 mm from reservoir to master cylinder - 1 m
Brake line remanufactured upon request, exclusively in 8 mm diameter copper.Photo not contractually binding. Supplied WITHOUT fittings - you can order the one you need from our store (for the master cylinder side). The other end is bare (inlet on ...
€50.40 TTC
(42,00 € HT)
(42,00 € HT)
7/16 banjo fitting + 7/16 hollow screw + seals
7/16 banjo fitting + 7/16 hollow screw + sealsDiameter male thread of the screw 11 mm
€32.82 TTC
(27,35 € HT)
(27,35 € HT)
Brake line - from 0 to 50 cm
Brake line remanufactured on demand only in copper diameter 6.35 mm. Small model, length less than 50 cm. Provide model (length and 2 original tips) Shipping after receipt of your model.
€47.64 TTC
(39,70 € HT)
(39,70 € HT)
Front brake cylinder 28.5mm -Panhard Dyna Z from 1958
Front wheel cylinder Dyna Z Panhard - from 1958 to the end - d 28.57 mm. G or D mounting.
€79.20 TTC
(66,00 € HT)
(66,00 € HT)
Special brake grease tube - Plastilub ATE - 75 ml
Tube of special braking grease (75 ml). ATE's Plastilube is used to lubricate the guide faces on calipers and brake linings and to protect them against corrosion.Note: The friction surfaces of the brake pads must not be coated with ATE Plastilube!
€13.80 TTC
(11,50 € HT)
(11,50 € HT)
Adapter fitting 1/2 UNF Male - 1/2 UNF female with internal bicone
Adapter fitting 1/2 UNF Male - 1/2 UNF female with internal bicone
€18.00 TTC
(15,00 € HT)
(15,00 € HT)
