
Male thread brake reservoir
Brake fluid reservoir. Supplied with bracket, plug and 3/4 male connector 16 threads / p. External thread diameter = 18.5 mm. Delivered without caliper (fixing by the thread on the master cylinder). Lockeed and silicone compatible
(33,80 € HT)
Brake line - from 200 to 250 cm
Brake line remanufactured on request, only in copper diameter 6.35 mm. Provide model (length and 2 original tips)Shipping after receipt of your model.
(63,70 € HT)
Brake line - from 0 to 50 cm
Brake line remanufactured on demand only in copper diameter 6.35 mm. Small model, length less than 50 cm. Provide model (length and 2 original tips) Shipping after receipt of your model.
(39,70 € HT)
Master cylinder 25.4 mm - Panhard Dyna Z
Complete master cylinder (piston d 25.4 mm). Fits Dyna Z 1954 thru June 1958.Piston 1 p or 25.4 mm1/2 output 20 f per inchEntry about 17 mm60 mm center distance for M 8 screws
(52,00 € HT)

Front brake cylinder 28.5mm -Panhard Dyna Z from 1958
Front wheel cylinder Dyna Z Panhard - from 1958 to the end - d 28.57 mm. G or D mounting.
(67,60 € HT)

Brake pipe - from 300 to 350 cm
Brake line remanufactured on request, only in copper diameter 6.35 mm. Provide model (length and 2 original tips)Shipping after receipt of your model.
(75,70 € HT)
Special brake grease tube - Plastilub ATE - 75 ml
Tube of special braking grease (75 ml). ATE's Plastilube is used to lubricate the guide faces on calipers and brake linings and to protect them against corrosion.Note: The friction surfaces of the brake pads must not be coated with ATE Plastilube!
(11,50 € HT)
Set of 4 relined brake shoes Panhard Dyna x86
Set of 4 relined brake shoes (front or rear) 195 mm x 30 mm in standard exchange for Panhard Dyna X86, Dyna Z, PL 17 and series 24Microblasting, varnish, industrial bonding of friction. Strong adhesion.Eliminates the problem of rivets that could ...
(98,00 € HT)

Cylinder - front copper seal kit for one wheel - Panhard Dyna Z
Set of 2 seals for hollow screw and banjo (for 1 cylinder)Internal Ø 11 mm and 15 mm
(3,40 € HT)

Set of 4 relined REAR 30mm larg - brake shoes - Panhard
Set of 4 relined brake shoes (front or rear) 195 mm x 30 mm in standard exchange for Panhard Dyna X86, Dyna Z, PL 17 and series 24Microblasting, varnish, industrial bonding of friction. Strong adhesion.Eliminates the problem of rivets that could ...
(85,00 € HT)

Metal insert tip for jar
Metal fitting to be fitted with the brake reservoir rubber to prevent the tearing and accidental draining of the brake fluid reservoir.
(8,85 € HT)
cFront left brake cylinder - d 31.75 mm - inclined - Panhard Z1
Front left brake cylinder - d 31.75 mm - inclined - Panhard Z1
(105,00 € HT)

Brake hose 445 mm front Dyna Z
Front brake hose Dyna Z Panhard - May 1958 at the end - length 445 mm
(25,00 € HT)
Ensemble banjo incliné 7/16 + vis creuse 7/16 - Panhard Z1 + joints
(55,00 € HT)
