Brake line - from 150 to 200 cm
Brake line re-manufactured on request, only in copper diameter 6.35 mm. Provide model (length and 2 original end pieces)Shipping after receiving your model.
€57.70 TTC
(57,70 € HT)
(57,70 € HT)
Brake pipe - from 300 to 350 cm
Brake line remanufactured on request, only in copper diameter 6.35 mm. Provide model (length and 2 original tips)Shipping after receipt of your model.
€75.70 TTC
(75,70 € HT)
(75,70 € HT)
Adapter fitting 1/2 UNF Male - 1/2 UNF female with internal bicone
Adapter fitting 1/2 UNF Male - 1/2 UNF female with internal bicone
€15.00 TTC
(15,00 € HT)
(15,00 € HT)
Brake line - from 0 to 50 cm
Brake line remanufactured on demand only in copper diameter 6.35 mm. Small model, length less than 50 cm. Provide model (length and 2 original tips) Shipping after receipt of your model.
€39.70 TTC
(39,70 € HT)
(39,70 € HT)
Ford Vedette 31.7mm front cylinder required
Front wheel cylinder repair kit, with pistons and spring. (For one wheel)Diam 31.75 mm
€22.50 TTC
(22,50 € HT)
(22,50 € HT)
Brake switch - stop - special silicone
Brake switch. STOP light function. 100% silicone liquid and LHM compatible1/2 - 20 thread / inch thread
€16.29 TTC
(16,29 € HT)
(16,29 € HT)
Special brake grease tube - Plastilub ATE - 75 ml
Tube of special braking grease (75 ml). ATE's Plastilube is used to lubricate the guide faces on calipers and brake linings and to protect them against corrosion.Note: The friction surfaces of the brake pads must not be coated with ATE Plastilube!
€11.50 TTC
(11,50 € HT)
(11,50 € HT)
Master cylinder Ford Vedette 25.4 mm - 1950-54 - Vendome Comete
" Ford Vedette d25.4 mm master cylinder - all models 1950 to 1954, Comète, Monte Carlo, Abeille, Vendôme. Attention special model for year 1949, also available in our shop. Delivered complete with bellows. "
€173.00 TTC
(173,00 € HT)
(173,00 € HT)
Brake reservoir with rubber
Translucent tank, delivered with bracket; rubber plug and fitting.
€32.00 TTC
(32,00 € HT)
(32,00 € HT)
Copper pipe fitting 7/16 - ext thread 11mm
Rigid brake line nut. 7/16 or about 11 mm measured on the external thread and Ø hole for the tube = 6.35mm
€5.30 TTC
(5,30 € HT)
(5,30 € HT)
Brake pipe - from 250 to 300 cm
Brake line remanufactured on request, only in copper diameter 6.35 mm. Provide model (length and 2 original tips)Shipping after receipt of your model.
€69.70 TTC
(69,70 € HT)
(69,70 € HT)
Pipe connector 1/2 20 UNF - tube 6.35 mm - external thread 12.5 mm
Rigid brake line nut. 1 / 2-20 UNF or Ø 12.5 mm - drilling for 6.35 mm tube (1/4 p)
€4.50 TTC
(4,50 € HT)
(4,50 € HT)
Front wheel 28.6 mm blind cylinder rebuild kit - Ford Vedette
Repair kit for front wheel cylinder 28.5 mm. Supplied with piston. Ford Vedette 1953 (4 per vehicle are needed)
€20.35 TTC
(20,35 € HT)
(20,35 € HT)
