Brake reservoir with rubber
Translucent tank, delivered with bracket; rubber plug and fitting.
€38.40 TTC
(32,00 € HT)
(32,00 € HT)
Rear brake cylinder 25.4 mm - 1954 - inclined exit - Ford Vedette
Rear wheel cylinder d 25.4mm, inclined pipe inlet. Montage 1953 and 1954. NON-CONTRACTUAL photo.
€60.60 TTC
(50,50 € HT)
(50,50 € HT)
Metal insert tip for jar
Metal fitting to be fitted with the brake reservoir rubber to prevent the tearing and accidental draining of the brake fluid reservoir.
€10.80 TTC
(9,00 € HT)
(9,00 € HT)
Silicone brake fluid DOT 5 - 1L
" DOT 5 100% silicone brake fluid - 1L can - Purple color - Do not mix with other types of brake fluids. The installation must be rinsed before changing the type of liquid. Photo not contractual. "
€53.95 TTC
(44,96 € HT)
(44,96 € HT)
Brake line - from 100 to 150 cm
" Brake line remanufactured on request, only in copper diameter 6.35 mm. . Provide model (length and 2 original end caps) Shipment after receipt of your model. "
€62.04 TTC
(51,70 € HT)
(51,70 € HT)
1/2 female 20 UNF connection on 8 mm tube (metal brake jar)
Metal tank foot nut (female 1/2 and d 8mm)
€11.10 TTC
(9,25 € HT)
(9,25 € HT)
Set of 4 Ford Vedette rear jaws - 1949 to 1952
Set of 4 rear brake shoes in standard exchange. (Send us your set before shipping the new one) High performance friction, applied by industrial gluing, no more rivets which damage the drums. Pickled and varnished jaws.
€144.00 TTC
(120,00 € HT)
(120,00 € HT)
Brake line - from 200 to 250 cm
Brake line remanufactured on request, only in copper diameter 6.35 mm. Provide model (length and 2 original tips)Shipping after receipt of your model.
€76.44 TTC
(63,70 € HT)
(63,70 € HT)
Brake reservoir with nipple + contact
Brake fluid reservoir, translucent plastic.With plug, fixing bracket and electrical contact for minimum liquid level
€48.00 TTC
(40,00 € HT)
(40,00 € HT)
Rear brake cylinder 25.4 mm - Ford Vedette
" Rear wheel cylinder repair kit, with pistons and spring. (For one wheel) Piston diameter = 25.4 mm "
€26.22 TTC
(21,85 € HT)
(21,85 € HT)
Special brake grease tube - Plastilub ATE - 75 ml
Tube of special braking grease (75 ml). ATE's Plastilube is used to lubricate the guide faces on calipers and brake linings and to protect them against corrosion.Note: The friction surfaces of the brake pads must not be coated with ATE Plastilube!
€13.80 TTC
(11,50 € HT)
(11,50 € HT)
Pipe Ø 8 mm from reservoir to master cylinder - 1 m
Brake line remanufactured upon request, exclusively in 8 mm diameter copper.Photo not contractually binding. Supplied WITHOUT fittings - you can order the one you need from our store (for the master cylinder side). The other end is bare (inlet on ...
€50.40 TTC
(42,00 € HT)
(42,00 € HT)
