Special brake grease tube - Plastilub ATE - 75 ml
Tube of special braking grease (75 ml). ATE's Plastilube is used to lubricate the guide faces on calipers and brake linings and to protect them against corrosion.Note: The friction surfaces of the brake pads must not be coated with ATE Plastilube!
€13.80 TTC
(11,50 € HT)
(11,50 € HT)
Rear brake cylinder 25.4 mm - 1949-53 Ford Vedette
Rear wheel cylinder d 25.4mm, Ford Vedette (1949 to August 1953), Vendôme, Comète, Monté Carlo, Abeille. Right pipe entry. NON-CONTRACTUAL photo.
€52.20 TTC
(43,50 € HT)
(43,50 € HT)
Front brake hose - Ford Vedette 1950 to 52
Front brake hose Ford Vedette June 1950 to 1952, Bee. Length 375 mm. NON-CONTRACTUAL photo.
€32.40 TTC
(27,00 € HT)
(27,00 € HT)
Adapter connection 1/2 UNF female - 3/8 UNF male
Braking adapter 1 / 2-20 UNF female by 3/8 24 male threads
€11.88 TTC
(9,90 € HT)
(9,90 € HT)
Front blind brake cylinder Ø 28.5 mm - 1953 - Ford Vedette
" 28.50 mm single piston cylinder mounted on front wheel - Left or right mounting - 2 cylinders (blind) per front wheel From September 1953. NON-CONTRACTUAL photo. "
€102.60 TTC
(85,50 € HT)
(85,50 € HT)
Front wheel 28.6 mm blind cylinder rebuild kit - Ford Vedette
Repair kit for front wheel cylinder 28.5 mm. Supplied with piston. Ford Vedette 1953 (4 per vehicle are needed)
€24.42 TTC
(20,35 € HT)
(20,35 € HT)
Raccord adaptateur 1/2 UNF mâle - 3/8 UNF femelle
Adaptateur freinage 1/2-20 UNF mâle par 3/8 24 filets femelle
€12.60 TTC
(10,50 € HT)
(10,50 € HT)
Front brake hose 380 mm - Ford Vedette 1949
Ford Vedette 1949 FRONT brake hose. Length 380 mm.
€30.00 TTC
(25,00 € HT)
(25,00 € HT)
Rear brake cylinder 25.4 mm - 1954 - inclined exit - Ford Vedette
Rear wheel cylinder d 25.4mm, inclined pipe inlet. Montage 1953 and 1954. NON-CONTRACTUAL photo.
€60.60 TTC
(50,50 € HT)
(50,50 € HT)
Pipe Ø 8 mm from reservoir to master cylinder - 1 m
Brake line remanufactured upon request, exclusively in 8 mm diameter copper.Photo not contractually binding. Supplied WITHOUT fittings - you can order the one you need from our store (for the master cylinder side). The other end is bare (inlet on ...
€50.40 TTC
(42,00 € HT)
(42,00 € HT)
Pipe connector 1/2 20 UNF - tube 6.35 mm - external thread 12.5 mm
Rigid brake line nut. 1 / 2-20 UNF or Ø 12.5 mm - drilling for 6.35 mm tube (1/4 p)
€5.40 TTC
(4,50 € HT)
(4,50 € HT)
Copper pipe fitting 7/16 - ext thread 11mm
Rigid brake line nut. 7/16 or about 11 mm measured on the external thread and Ø hole for the tube = 6.35mm
€6.36 TTC
(5,30 € HT)
(5,30 € HT)
