
Contactor: copper seal kit for LONG stop contactor 022114
Set of 2 seals for STOP LONG contactor
(3,00 € HT)

Copper pipe fitting 7/16 - ext thread 11mm
Rigid brake line nut. 7/16 or about 11 mm measured on the external thread and Ø hole for the tube = 6.35mm
(5,00 € HT)
Front brake cylinder 31.7 mm - Ford Vedette 54 and Abeille
Front wheel cylinder d 31.75 mm - Ford Commercial Vedette type Abeille and some Vedette 1954. (Check your model carefully before ordering).
(40,50 € HT)

Set of 4 front jaws Ford Vedette
" Set of 4 front brake shoes in standard exchange. (Send us your set before shipping the new one) High performance friction, applied by industrial bonding, no more rivets which damage the drums. Pickled and varnished jaws. (non contractual photo) "
(132,00 € HT)

Rear brake cylinder 25.4 mm - 1949-53 Ford Vedette
Rear wheel cylinder d 25.4mm, Ford Vedette (1949 to August 1953), Vendôme, Comète, Monté Carlo, Abeille. Right pipe entry. NON-CONTRACTUAL photo.
(40,25 € HT)

Brake line - from 51 to 99 cm
Brake line remanufactured on request, only in copper diameter 6.35 mm. Large model, length from 50 cm, max 2m. Provide model (length and 2 original tips)Shipping after receiving your model.
(42,00 € HT)
Special brake grease tube - Plastilub ATE - 75 ml
Tube of special braking grease (75 ml). ATE's Plastilube is used to lubricate the guide faces on calipers and brake linings and to protect them against corrosion.Note: The friction surfaces of the brake pads must not be coated with ATE Plastilube!
(11,50 € HT)
Rear brake cylinder 25.4 mm - 1954 - inclined exit - Ford Vedette
Rear wheel cylinder d 25.4mm, inclined pipe inlet. Montage 1953 and 1954. NON-CONTRACTUAL photo.
(46,25 € HT)

Special brake grease tube - 5g
Tube of special braking grease (5gr), Lockheed DOT and silicone compatible, protects steel cylinder and piston parts, helps them slide, compatible with rubber parts.
(3,89 € HT)
Brake switch - stop - DOT 3 and 4
" Brake switch. STOP light function - compatible with synthetic liquid type" "lockheed" "Dot 3 and 4. If using 100% silicone liquid: Choose this other reference 1/2 - 20 thread / inch thread "
(15,83 € HT)
Brake line - from 150 to 200 cm
Brake line re-manufactured on request, only in copper diameter 6.35 mm. Provide model (length and 2 original end pieces)Shipping after receiving your model.
(88,00 € HT)
Master cylinder Ford Vedette 25.4 mm - 1950-54 - Vendome Comete
" Ford Vedette d25.4 mm master cylinder - all models 1950 to 1954, Comète, Monte Carlo, Abeille, Vendôme. Attention special model for year 1949, also available in our shop. Delivered complete with bellows. "
(160,90 € HT)

Pipe connector 1/2 20 UNF - tube 6.35 mm - external thread 12.5 mm
Rigid brake line nut. 1 / 2-20 UNF or Ø 12.5 mm - drilling for 6.35 mm tube (1/4 p)
(4,17 € HT)
Brake line - from 200 to 250 cm
Brake line remanufactured on request, only in copper diameter 6.35 mm. Provide model (length and 2 original tips)Shipping after receipt of your model.
(128,00 € HT)
Metal insert tip for jar
Metal fitting to be fitted with the brake reservoir rubber to prevent the tearing and accidental draining of the brake fluid reservoir.
(8,50 € HT)