Ford Vedette 31.7mm front cylinder required
Front wheel cylinder repair kit, with pistons and spring. (For one wheel)Diam 31.75 mm
€27.00 TTC
(22,50 € HT)
(22,50 € HT)
Front brake hose - Ford Vedette 1953 -54
FRONT brake hose Ford Vedette 1953 and 54, Vendôme, Comète, Monte Carlo Length 322 mm. NON-CONTRACTUAL photo
€32.40 TTC
(27,00 € HT)
(27,00 € HT)
Rear brake cylinder 25.4 mm - 1954 - inclined exit - Ford Vedette
Rear wheel cylinder d 25.4mm, inclined pipe inlet. Montage 1953 and 1954. NON-CONTRACTUAL photo.
€60.60 TTC
(50,50 € HT)
(50,50 € HT)
Set of 4 Ford Vedette rear jaws - 1949 to 1952
Set of 4 rear brake shoes in standard exchange. (Send us your set before shipping the new one) High performance friction, applied by industrial gluing, no more rivets which damage the drums. Pickled and varnished jaws.
€144.00 TTC
(120,00 € HT)
(120,00 € HT)
Front wheel 28.6 mm blind cylinder rebuild kit - Ford Vedette
Repair kit for front wheel cylinder 28.5 mm. Supplied with piston. Ford Vedette 1953 (4 per vehicle are needed)
€24.42 TTC
(20,35 € HT)
(20,35 € HT)
Front brake hose - Ford Vedette 1950 to 52
Front brake hose Ford Vedette June 1950 to 1952, Bee. Length 375 mm. NON-CONTRACTUAL photo.
€32.40 TTC
(27,00 € HT)
(27,00 € HT)
Pipe connection 1/2 20 UNF - 8 mm tube - special jar - 12.5 mm thread ext.
Rigid brake line nut. 1 / 2-20 UNF i.e. Ø 12.5 mm - drilling for 8 mm tube special brake reservoir
€6.18 TTC
(5,15 € HT)
(5,15 € HT)
3/8 - 24 f copper pipe fitting
Rigid brake line nut. 3/8 x 24 threads / inch. Tube Ø 4.75 mm
€7.80 TTC
(6,50 € HT)
(6,50 € HT)
Brake pipe - from 250 to 300 cm
Brake line remanufactured on request, only in copper diameter 6.35 mm. Provide model (length and 2 original tips)Shipping after receipt of your model.
€83.64 TTC
(69,70 € HT)
(69,70 € HT)
copy of Set of 4 Ford Vedette rear jaws - 1954
Set of 4 rear brake shoes in standard exchange. (Send us your set before shipping the new one) High performance friction, applied by industrial gluing, no more rivets which damage the drums. Pickled and varnished jaws.
€158.40 TTC
(132,00 € HT)
(132,00 € HT)
Pipe Ø 8 mm from reservoir to master cylinder - 1 m
Brake line remanufactured upon request, exclusively in 8 mm diameter copper.Photo not contractually binding. Supplied WITHOUT fittings - you can order the one you need from our store (for the master cylinder side). The other end is bare (inlet on ...
€50.40 TTC
(42,00 € HT)
(42,00 € HT)
Special brake grease tube - Plastilub ATE - 75 ml
Tube of special braking grease (75 ml). ATE's Plastilube is used to lubricate the guide faces on calipers and brake linings and to protect them against corrosion.Note: The friction surfaces of the brake pads must not be coated with ATE Plastilube!
€13.80 TTC
(11,50 € HT)
(11,50 € HT)
Brake line - from 51 to 99 cm
Brake line remanufactured on request, only in copper diameter 6.35 mm. Large model, length from 50 cm, max 2m. Provide model (length and 2 original tips)Shipping after receiving your model.
€54.84 TTC
(45,70 € HT)
(45,70 € HT)
