Front brake cylinder 31.7 mm - Ford Vedette 54 and Abeille
Front wheel cylinder d 31.75 mm - Ford Commercial Vedette type Abeille and some Vedette 1954. (Check your model carefully before ordering).
€52.80 TTC
(44,00 € HT)
(44,00 € HT)
Brake line - from 0 to 50 cm
Brake line remanufactured on demand only in copper diameter 6.35 mm. Small model, length less than 50 cm. Provide model (length and 2 original tips) Shipping after receipt of your model.
€47.64 TTC
(39,70 € HT)
(39,70 € HT)
1/2 female 20 UNF connection on 8 mm tube (metal brake jar)
Metal tank foot nut (female 1/2 and d 8mm)
€11.10 TTC
(9,25 € HT)
(9,25 € HT)
Special brake grease tube - 5g
Tube of special braking grease (5gr), Lockheed DOT and silicone compatible, protects steel cylinder and piston parts, helps them slide, compatible with rubber parts.
€4.67 TTC
(3,89 € HT)
(3,89 € HT)
Master cylinder kit Ø 25.4 mm - Ford Vedette
Repair kit for Ford Vedette d 25.4mm master cylinder from 1949 to 54.
€27.00 TTC
(22,50 € HT)
(22,50 € HT)
Set of 4 Ford Vedette rear jaws - 1949 to 1952
Set of 4 rear brake shoes in standard exchange. (Send us your set before shipping the new one) High performance friction, applied by industrial gluing, no more rivets which damage the drums. Pickled and varnished jaws.
€144.00 TTC
(120,00 € HT)
(120,00 € HT)
Brake reservoir with nipple + contact
Brake fluid reservoir, translucent plastic.With plug, fixing bracket and electrical contact for minimum liquid level
€48.00 TTC
(40,00 € HT)
(40,00 € HT)
Front brake hose - Ford Vedette 1953 -54
FRONT brake hose Ford Vedette 1953 and 54, Vendôme, Comète, Monte Carlo Length 322 mm. NON-CONTRACTUAL photo
€32.40 TTC
(27,00 € HT)
(27,00 € HT)
Brake line - from 200 to 250 cm
Brake line remanufactured on request, only in copper diameter 6.35 mm. Provide model (length and 2 original tips)Shipping after receipt of your model.
€76.44 TTC
(63,70 € HT)
(63,70 € HT)
Set of 4 front jaws Ford Vedette
" Set of 4 front brake shoes in standard exchange. (Send us your set before shipping the new one) High performance friction, applied by industrial bonding, no more rivets which damage the drums. Pickled and varnished jaws. (non contractual photo) "
€132.00 TTC
(110,00 € HT)
(110,00 € HT)
Copper pipe fitting 7/16 - ext thread 11mm
Rigid brake line nut. 7/16 or about 11 mm measured on the external thread and Ø hole for the tube = 6.35mm
€6.36 TTC
(5,30 € HT)
(5,30 € HT)
Rubber teat end for brake reservoir
" Flexible connection for brake reservoir. (100% rubber compatible with lockheed and silicone) Must be fitted with the metal insert to prevent tearing and accidental emptying of the liquid reservoir. "
€11.40 TTC
(9,50 € HT)
(9,50 € HT)
