FRONT RIGHT 28.5mm brake cylinder - Panhard PL 17 - 60 to 62
Front wheel cylinder L PL17 from 1960 to March 62 - d 28.57 mm. Entry 3/8 - Right mounting. Length 72 mm - inside liquid passage = 8.5 mm
€81.60 TTC
(68,00 € HT)
(68,00 € HT)
Adapter fitting 3/8 UNF Male - 10x100 female
Adapter fitting 3/8 UNF Male - 10x100 female
€19.20 TTC
(16,00 € HT)
(16,00 € HT)
Metal insert tip for jar
Metal fitting to be fitted with the brake reservoir rubber to prevent the tearing and accidental draining of the brake fluid reservoir.
€10.62 TTC
(8,85 € HT)
(8,85 € HT)
Set of 4 relined brake shoes Panhard Dyna x86
Set of 4 relined brake shoes (front or rear) 195 mm x 30 mm in standard exchange for Panhard Dyna X86, Dyna Z, PL 17 and series 24Microblasting, varnish, industrial bonding of friction. Strong adhesion.Eliminates the problem of rivets that could ...
€117.60 TTC
(98,00 € HT)
(98,00 € HT)
Adapter connection 7/16 male - 3/8 female
Adaptateur freinage mâle 7/16 (envion 11mm) femelle 3/8
€21.00 TTC
(17,50 € HT)
(17,50 € HT)
Rear brake cylinder 19mm - 3/8 Panhard 24 - 07/1964 to end
Rear wheel cylinder 19mm - Panhard 24 équipé frein à tambours - 07/1964 à fin de série
€69.12 TTC
(57,60 € HT)
(57,60 € HT)
Copper pipe fitting 7/16 - ext thread 11mm
Rigid brake line nut. 7/16 or about 11 mm measured on the external thread and Ø hole for the tube = 6.35mm
€6.24 TTC
(5,20 € HT)
(5,20 € HT)
Adapter connection 7/16 male - 1/2 female
Adaptateur freinage mâle 7/16 (envion 11mm)femelle 11/16 pour recevoir gros flexible (17mm mâle
€18.00 TTC
(15,00 € HT)
(15,00 € HT)
Brake line - from 100 to 150 cm
" Brake line remanufactured on request, only in copper diameter 6.35 mm. . Provide model (length and 2 original end caps) Shipment after receipt of your model. "
€79.20 TTC
(66,00 € HT)
(66,00 € HT)
7/16 banjo fitting + 7/16 hollow screw + seals
7/16 banjo fitting + 7/16 hollow screw + sealsDiameter male thread of the screw 11 mm
€33.54 TTC
(27,95 € HT)
(27,95 € HT)
Special brake grease tube - Plastilub ATE - 75 ml
Tube of special braking grease (75 ml). ATE's Plastilube is used to lubricate the guide faces on calipers and brake linings and to protect them against corrosion.Note: The friction surfaces of the brake pads must not be coated with ATE Plastilube!
€13.80 TTC
(11,50 € HT)
(11,50 € HT)
Ensemble banjo incliné 7/16 + vis creuse 7/16 - Panhard Z1 + joints