Set of 4 relined REAR brake shoes - Panhard
Set of 4 relined brake shoes (front or rear) 195 mm x 30 mm in standard exchange for Panhard Dyna X86, Dyna Z, PL 17 and series 24Microblasting, varnish, industrial bonding of friction. Strong adhesion.Eliminates the problem of rivets that could ...
€117.60 TTC
(98,00 € HT)
(98,00 € HT)
Pipe Ø 8 mm from reservoir to master cylinder - 1 m
Brake line remanufactured upon request, exclusively in 8 mm diameter copper.Photo not contractually binding. Supplied WITHOUT fittings - you can order the one you need from our store (for the master cylinder side). The other end is bare (inlet on ...
€50.40 TTC
(42,00 € HT)
(42,00 € HT)
Rear brake cylinder 19 mm - Panhard Dyna X 86 - 04/1950 at the end
Rear brake cylinder Ø 19 mm - Panhard Dyna X 86 - 04/1950 to endSteel body length: 54 mmFlange hole: 31.8 mmFixing center distance: 25 mm - M6 mm thread
€66.12 TTC
(55,10 € HT)
(55,10 € HT)
Rear wheel brake hose - 250 mm Panhard Dyna
Rear wheel brake hose - 250 mm Panhard Dyna - 17 mm male end. Made in France
€30.00 TTC
(25,00 € HT)
(25,00 € HT)
Adapter fitting 1/2 UNF Male - 1/2 UNF female with internal bicone
Adapter fitting 1/2 UNF Male - 1/2 UNF female with internal bicone
€18.00 TTC
(15,00 € HT)
(15,00 € HT)
Male thread brake reservoir
Brake fluid reservoir. Supplied with bracket, plug and 3/4 male connector 16 threads / p. External thread diameter = 18.5 mm. Delivered without caliper (fixing by the thread on the master cylinder). Lockeed and silicone compatible
€42.00 TTC
(35,00 € HT)
(35,00 € HT)
Adapter fitting 7/16 Male - 7/16 female outgoing cone
Adapter fitting 7/16 Male - 7/16 female outgoing cone
€19.56 TTC
(16,30 € HT)
(16,30 € HT)
Brake pipe - from 250 to 300 cm
Brake line remanufactured on request, only in copper diameter 6.35 mm. Provide model (length and 2 original tips)Shipping after receipt of your model.
€83.64 TTC
(69,70 € HT)
(69,70 € HT)
Special brake grease tube - Plastilub ATE - 75 ml
Tube of special braking grease (75 ml). ATE's Plastilube is used to lubricate the guide faces on calipers and brake linings and to protect them against corrosion.Note: The friction surfaces of the brake pads must not be coated with ATE Plastilube!
€13.80 TTC
(11,50 € HT)
(11,50 € HT)
Master cylinder 25.4 mm Panhard Dyna X 86 - April 1950 and +
Master cylinder 25.4 mm Panhard Dyna - April 1950 and +Piston 1 inch or 25.4 mm1/2 output 20 f per inchEntry about 17 mm60 mm center distance for M 8 screws
€64.80 TTC
(54,00 € HT)
(54,00 € HT)
