Rubber bush kit - silentblocs for Ford Vedette front axle
Kit including dust covers and other grease covers to remake the front axle, including those for the stabilizer bar. The set includes:4 x ring (ref Ford 3193)4 x steering ball joint grease cover4 x grease cover on upper triangle axle - chassis ...
€556.20 TTC
(463,50 € HT)
(463,50 € HT)
Steering relay - Ford vedette - Vendôme - Comet
Steering relay attached to the passenger side chassis. Remember to replace the tie rod with the 2 rotation nuts to remove wear clearances.
€236.00 TTC
(236,00 € HT)
(236,00 € HT)
Front hub kit - Ford Vedette - Vendome
Front wheel hub kit. Includes:- 1 internal conical bearing- 1 external conical bearingThe set is valid for one front wheel.
€129.60 TTC
(108,00 € HT)
(108,00 € HT)
Ford Vedette stabilizer bar support
Mounting bracket for stabilizer bar. 2 per vehicle - Sold individually.
€31.80 TTC
(26,50 € HT)
(26,50 € HT)
Spinnaker ring on 1/2 rear shaft - Ford Vedette - Comete
Spinnaker ring on 1/2 rear shaft - Ford Vedette - Comete(to be mounted on the left and right side)
€18.40 TTC
(15,33 € HT)
(15,33 € HT)
Gearbox or axle oil SAE 80-140 - IGOL - 1L
Viscosity index 80 - 140API GL-4(Not suitable for Peugeot type screw axles)
€24.00 TTC
(20,00 € HT)
(20,00 € HT)
Ford Vedette gearbox inlet seal ring
Sealing ring (oil seal) placed at the Ford Vedette gearbox outlet.35 x 51
€17.00 TTC
(14,17 € HT)
(14,17 € HT)
Upper and lower adjustment for Ford vedette front hub
Allows adjustment of the camber on the front axle. When these parts are worn, play appears making it impossible to adjust the geometry of the front axle and making the vehicle's driving imprecise.Sold individually (2 per front hub)
€96.00 TTC
(96,00 € HT)
(96,00 € HT)
Grease cover on upper triangle wheel side - Ford Vedette
Protection mounted on the upper arm on the wheel pivot side - Ford reference - 3075 - 4 per vehicle - Sold individually.
€20.40 TTC
(17,00 € HT)
(17,00 € HT)
160 mm float fuel gauge - 6V
" Float fuel gauge. Adaptable model. Arm length approx. 160 mm. External diameter of plate 54 mm - fixing center distance 38 mm. Supplied with cork seal. 3-hole fixing. Internal resistance approx. 110 ohms. For 6-volt vehicle only. "
€48.00 TTC
(40,00 € HT)
(40,00 € HT)
Ford Vedette rear suspension blade bush
" Silent block to be mounted in the eyelets of the rear suspension blades - 6 pieces per suspension (or 12 on a vehicle) - Sold individually D int = 12 mm D ext = 20.5 mm approximately D ext with collar = 30 mm Long without collar = 22 mm "
€16.20 TTC
(13,50 € HT)
(13,50 € HT)
Ford Vedette steering ball joint cover
Rubber protection for steering ball joint - 4 per vehicle - Sold individually
€18.30 TTC
(15,25 € HT)
(15,25 € HT)
Set of 2 pivot 1953-54 Ford Vedette Comete Vendome
Set of 2 pivots (in standard exchange), ready to install. The set includes 1 pivot G + 1 pivot D, new bronze bushings, treated steel pivot pins, rectified axis line.Mounts on- Ford Vedette 1954- some Vedette 1953Another reference is available for ...
€426.20 TTC
(426,20 € HT)
(426,20 € HT)
Ring x 2 - gearbox lever or column foot - Ford Vedette and derivatives
Set of 2 repair rings to replace the silent blocks of the gearbox levers or those at the bottom of the column - Ford Vedette and derivatives.Requires 2 sets per vehicle
€32.00 TTC
(32,00 € HT)
(32,00 € HT)
Ford Vedette gearbox support
Support for gearbox cross member. You need 2 per vehicle. Sold individually.
€36.00 TTC
(30,00 € HT)
(30,00 € HT)
Jeu rotules direction ford vedette sans manchon