
Tie rod ends - Ford Vedette
Set of steering ball joints for Ford Vedette 1949 to 54, Abeille, Vendôme, Comète, Monte Carlo.Includes:- 1 x long ball joint,- 1 x short ball joint.(the adjusting sleeve is not supplied)
(169,20 € HT)
Ford Vedette gearbox primary shaft groove bearing
Bearing 40x80x18 with locking groove, special Ford Vedette gearbox
(45,67 € HT)
160 mm float fuel gauge - 6V
" Float fuel gauge. Adaptable model. Arm length approx. 160 mm. External diameter of plate 54 mm - fixing center distance 38 mm. Supplied with cork seal. 3-hole fixing. Internal resistance approx. 110 ohms. For 6-volt vehicle only. "
(40,00 € HT)
Steering tie rod with 2 tie nuts - Ford Vedette - Vendôme - Comète
Steering rod connecting the relay on the chassis to the steering box's output rod. Supplied with two connecting nuts.Don't forget to replace the relay on the chassis (passenger side).
(300,00 € HT)
Front hub kit - Ford Vedette - Vendome
Front wheel hub kit. Includes:- 1 internal conical bearing- 1 external conical bearingThe set is valid for one front wheel.
(108,00 € HT)
Ford Vedette spinnaker seal ring
Sealing ring with steel strapping (metallic spinnaker seal) placed on the Ford Vedette bridge nose.
(26,19 € HT)
Ring x 2 - gearbox lever or column foot - Ford Vedette and derivatives
Set of 2 repair rings to replace the silent blocks of the gearbox levers or those at the bottom of the column - Ford Vedette and derivatives.Requires 2 sets per vehicle
(32,00 € HT)
Ford Vedette stabilizer bar support
Mounting bracket for stabilizer bar. 2 per vehicle - Sold individually.
(26,50 € HT)
Grease cover on upper triangle frame side - Ford Vedette
Rubber protection mounted on upper triangle - Ford reference (3196) - 4 per vehicle - Sold individually.
(20,00 € HT)
Pair of rear shocks Ford Vedette -
" Rear shock absorbers for Ford Vedette all models. Record brand, 100% conforms to the original assembly. Price per pair. "
(232,50 € HT)
Ford Vedette rear suspension blade bush
" Silent block to be mounted in the eyelets of the rear suspension blades - 6 pieces per suspension (or 12 on a vehicle) - Sold individually D int = 12 mm D ext = 20.5 mm approximately D ext with collar = 30 mm Long without collar = 22 mm "
(13,50 € HT)
Kit 2 x Ford Vedette pivots
" Ford Vedette front pivot repair kit for all models, Bee, Comet, Monte Carlo, Vendôme. Includes 2 pins and 4 bronze bushings. (for 2 wheels). The 2 axes are in treated steel for a much greater hardness than ordinary commercial products. ...
(202,60 € HT)
Rubber bush kit - silentblocs for Ford Vedette front axle
Kit including dust covers and other grease covers to remake the front axle, including those for the stabilizer bar. The set includes:4 x ring (ref Ford 3193)4 x steering ball joint grease cover4 x grease cover on upper triangle axle - chassis ...
(463,50 € HT)
Set of 2 pivot 1953-54 Ford Vedette Comete Vendome
Set of 2 pivots (in standard exchange), ready to install. The set includes 1 pivot G + 1 pivot D, new bronze bushings, treated steel pivot pins, rectified axis line.Mounts on- Ford Vedette 1954- some Vedette 1953Another reference is available for ...
(426,20 € HT)
Drive shaft spacers - Ford Vedette
Drive shaft spider. 2 per tree - Sold individually.
(50,00 € HT)