- New
Ford Vedette rear suspension blade bush
" Silent block to be mounted in the eyelets of the rear suspension blades - 6 pieces per suspension (or 12 on a vehicle) - Sold individually D int = 12 mm D ext = 20.5 mm approximately D ext with collar = 30 mm Long without collar = 22 mm "
€16.20 TTC
(13,50 € HT)
(13,50 € HT)
Upper and lower adjustment for Ford vedette front hub
Allows adjustment of the camber on the front axle. When these parts are worn, play appears making it impossible to adjust the geometry of the front axle and making the vehicle's driving imprecise.Sold individually (2 per front hub)
€96.00 TTC
(96,00 € HT)
(96,00 € HT)
Front drum spinnaker Ford Vedette 1949-52
Front drum sealing ring Ford Vedette 1949 to 52 - Delivered individually.(Non contractual photo)
€23.87 TTC
(19,89 € HT)
(19,89 € HT)
Spinnaker ring on 1/2 rear shaft - Ford Vedette - Comete
Spinnaker ring on 1/2 rear shaft - Ford Vedette - Comete(to be mounted on the left and right side)
€18.40 TTC
(15,33 € HT)
(15,33 € HT)
Ford Vedette steering ball joint cover
Rubber protection for steering ball joint - 4 per vehicle - Sold individually
€18.30 TTC
(15,25 € HT)
(15,25 € HT)
Ford Vedette gearbox primary shaft groove bearing
Bearing 40x80x18 with locking groove, special Ford Vedette gearbox
€54.80 TTC
(45,67 € HT)
(45,67 € HT)
Ford Vedette stabilizer bar bush
Silent block for Ford Vedette stabilizer bar - 4 per side or 8 for a vehicle - Sold individually.
€15.60 TTC
(13,00 € HT)
(13,00 € HT)
Front hub kit - Ford Vedette - Vendome
Front wheel hub kit. Includes:- 1 internal conical bearing- 1 external conical bearingThe set is valid for one front wheel.
€129.60 TTC
(108,00 € HT)
(108,00 € HT)
160 mm float fuel gauge - 6V
" Float fuel gauge. Adaptable model. Arm length approx. 160 mm. External diameter of plate 54 mm - fixing center distance 38 mm. Supplied with cork seal. 3-hole fixing. Internal resistance approx. 110 ohms. For 6-volt vehicle only. "
€48.00 TTC
(40,00 € HT)
(40,00 € HT)
Ford Vedette stabilizer bar support
Mounting bracket for stabilizer bar. 2 per vehicle - Sold individually.
€31.80 TTC
(26,50 € HT)
(26,50 € HT)
Ford Vedette gearbox inlet seal ring
Sealing ring (oil seal) placed at the Ford Vedette gearbox outlet.35 x 51
€17.00 TTC
(14,17 € HT)
(14,17 € HT)
Grease cover on lower triangle wheel side - Ford Vedette
Rubber ring for Ford Vedette front axle - on lower pivot - 4 per vehicle - Sold individually Ford Ref = 3193
€19.20 TTC
(16,00 € HT)
(16,00 € HT)
Set of 2 Ford Vedette pivots 1949-52
Set of 2 pivots (in standard exchange), ready to install. The set includes 1 pivot G + 1 pivot D, new bronze bushings, treated steel pivot pins, rectified axis line.Mounts on:- Ford Vedette from 1949 to 52- some Vedette 1953- Comète 13 and 22cv, ...
€426.20 TTC
(426,20 € HT)
(426,20 € HT)
Tie rod ends - Ford Vedette
Set of steering ball joints for Ford Vedette 1949 to 54, Abeille, Vendôme, Comète, Monte Carlo.Includes:- 1 x long ball joint,- 1 x short ball joint.(the adjusting sleeve is not supplied)
€169.20 TTC
(169,20 € HT)
(169,20 € HT)
Ford Vedette gearbox support
Support for gearbox cross member. You need 2 per vehicle. Sold individually.
€36.00 TTC
(30,00 € HT)
(30,00 € HT)
