Front hub kit - Ford Vedette - Vendome
Front wheel hub kit. Includes:- 1 internal conical bearing- 1 external conical bearingThe set is valid for one front wheel.
€129.60 TTC
(108,00 € HT)
(108,00 € HT)
Front drum spinnaker Ford Vedette 1949-52
Front drum sealing ring Ford Vedette 1949 to 52 - Delivered individually.(Non contractual photo)
€23.87 TTC
(19,89 € HT)
(19,89 € HT)
Ford Vedette gearbox support
Support for gearbox cross member. You need 2 per vehicle. Sold individually.
€25.00 TTC
(20,83 € HT)
(20,83 € HT)
Ball joints with steering arms - Ford Vedette
Steering arm for Ford Vedette 1949 to 54, Abeille, Vendôme, Comète, Monte Carlo.Includes:- 1 x long ball joint,- 1 x short ball joint,- 1 x adjustment sleeve.
€211.80 TTC
(211,80 € HT)
(211,80 € HT)
Ford Vedette gearbox inlet seal ring
Sealing ring (oil seal) placed at the Ford Vedette gearbox outlet.35 x 51
€17.00 TTC
(14,17 € HT)
(14,17 € HT)
160 mm float fuel gauge - 6V
" Float fuel gauge. Adaptable model. Arm length approx. 160 mm. External diameter of plate 54 mm - fixing center distance 38 mm. Supplied with cork seal. 3-hole fixing. Internal resistance approx. 110 ohms. For 6-volt vehicle only. "
€59.90 TTC
(49,92 € HT)
(49,92 € HT)
Kit 2 x Ford Vedette pivots
" Ford Vedette front pivot repair kit for all models, Bee, Comet, Monte Carlo, Vendôme. Includes 2 pins and 4 bronze bushings. (for 2 wheels). The 2 axes are in treated steel for a much greater hardness than ordinary commercial products. ...
€202.60 TTC
(202,60 € HT)
(202,60 € HT)
Ford Vedette rear suspension blade bush
" Silent block to be mounted in the eyelets of the rear suspension blades - 6 pieces per suspension (or 12 on a vehicle) - Sold individually D int = 12 mm D ext = 20.5 mm approximately D ext with collar = 30 mm Long without collar = 22 mm "
€14.34 TTC
(11,95 € HT)
(11,95 € HT)
Set of 2 Ford Vedette pivots 1949-52
Set of 2 pivots (in standard exchange), ready to install. The set includes 1 pivot G + 1 pivot D, new bronze bushings, treated steel pivot pins, rectified axis line.Mounts on:- Ford Vedette from 1949 to 52- some Vedette 1953- Comète 13 and 22cv, ...
€426.20 TTC
(426,20 € HT)
(426,20 € HT)
Ford Vedette gearbox primary shaft groove bearing
Bearing 40x80x18 with locking groove, special Ford Vedette gearbox
€54.80 TTC
(45,67 € HT)
(45,67 € HT)
Grease cover on upper triangle frame side - Ford Vedette
Rubber protection mounted on upper triangle - Ford reference (3196) - 4 per vehicle - Sold individually.
€16.52 TTC
(13,77 € HT)
(13,77 € HT)
IGOL Rallye Gear axle transmission oil SAE 75 80 90 - GL4
Oil for gearbox and bridge for old mechanics. Type SAE 75 80 90 - GL4. 1L container.(Not suitable for Peugeot type screw axles)
€20.00 TTC
(16,67 € HT)
(16,67 € HT)
Ford Vedette gearbox outlet seal ring
Sealing ring (oil seal) placed at the Ford Vedette gearbox outlet.
€17.00 TTC
(14,17 € HT)
(14,17 € HT)
Ford Vedette stabilizer bar bush
Silent block for Ford Vedette stabilizer bar - 4 per side or 8 for a vehicle - Sold individually.
€13.40 TTC
(11,17 € HT)
(11,17 € HT)
Tie rod ends - Ford Vedette
Set of steering ball joints for Ford Vedette 1949 to 54, Abeille, Vendôme, Comète, Monte Carlo.Includes:- 1 x long ball joint,- 1 x short ball joint.(the adjusting sleeve is not supplied)
€169.20 TTC
(169,20 € HT)
(169,20 € HT)
Ford Vedette spinnaker seal ring
Sealing ring with steel strapping (metallic spinnaker seal) placed on the Ford Vedette bridge nose.
€31.43 TTC
(26,19 € HT)
(26,19 € HT)
