Ford Vedette gearbox outlet seal ring
Sealing ring (oil seal) placed at the Ford Vedette gearbox outlet.
€17.00 TTC
(14,17 € HT)
(14,17 € HT)
160 mm float fuel gauge - 6V
" Float fuel gauge. Adaptable model. Arm length approx. 160 mm. External diameter of plate 54 mm - fixing center distance 38 mm. Supplied with cork seal. 3-hole fixing. Internal resistance approx. 110 ohms. For 6-volt vehicle only. "
€48.00 TTC
(40,00 € HT)
(40,00 € HT)
Set of 2 Ford Vedette pivots 1949-52
Set of 2 pivots (in standard exchange), ready to install. The set includes 1 pivot G + 1 pivot D, new bronze bushings, treated steel pivot pins, rectified axis line.Mounts on:- Ford Vedette from 1949 to 52- some Vedette 1953- Comète 13 and 22cv, ...
€426.20 TTC
(426,20 € HT)
(426,20 € HT)
Upper and lower adjustment for Ford vedette front hub
Allows adjustment of the camber on the front axle. When these parts are worn, play appears making it impossible to adjust the geometry of the front axle and making the vehicle's driving imprecise.Sold individually (2 per front hub)
€96.00 TTC
(96,00 € HT)
(96,00 € HT)
Ford Vedette rear suspension blade bush
" Silent block to be mounted in the eyelets of the rear suspension blades - 6 pieces per suspension (or 12 on a vehicle) - Sold individually D int = 12 mm D ext = 20.5 mm approximately D ext with collar = 30 mm Long without collar = 22 mm "
€16.20 TTC
(13,50 € HT)
(13,50 € HT)
Grease cover on upper triangle wheel side - Ford Vedette
Protection mounted on the upper arm on the wheel pivot side - Ford reference - 3075 - 4 per vehicle - Sold individually.
€20.40 TTC
(17,00 € HT)
(17,00 € HT)
Tie rod ends - Ford Vedette
Set of steering ball joints for Ford Vedette 1949 to 54, Abeille, Vendôme, Comète, Monte Carlo.Includes:- 1 x long ball joint,- 1 x short ball joint.(the adjusting sleeve is not supplied)
€176.00 TTC
(176,00 € HT)
(176,00 € HT)
Ford Vedette gearbox inlet seal ring
Sealing ring (oil seal) placed at the Ford Vedette gearbox outlet.35 x 51
€17.00 TTC
(14,17 € HT)
(14,17 € HT)
Rubber bush kit - silentblocs for Ford Vedette front axle
Kit including dust covers and other grease covers to remake the front axle, including those for the stabilizer bar. The set includes:4 x ring (ref Ford 3193)4 x steering ball joint grease cover4 x grease cover on upper triangle axle - chassis ...
€556.20 TTC
(463,50 € HT)
(463,50 € HT)
Set of 2 pivot 1953-54 Ford Vedette Comete Vendome
Set of 2 pivots (in standard exchange), ready to install. The set includes 1 pivot G + 1 pivot D, new bronze bushings, treated steel pivot pins, rectified axis line.Mounts on- Ford Vedette 1954- some Vedette 1953Another reference is available for ...
€426.20 TTC
(426,20 € HT)
(426,20 € HT)
Kit 2 x Ford Vedette pivots
" Ford Vedette front pivot repair kit for all models, Bee, Comet, Monte Carlo, Vendôme. Includes 2 pins and 4 bronze bushings. (for 2 wheels). The 2 axes are in treated steel for a much greater hardness than ordinary commercial products. ...
€202.60 TTC
(202,60 € HT)
(202,60 € HT)
Rear hub oil seal Ford Vedette Vendome Comete
Rear drum sealing ring - (Non contractual photo)
€30.00 TTC
(25,00 € HT)
(25,00 € HT)
Ford Vedette gearbox support
Support for gearbox cross member. You need 2 per vehicle. Sold individually.
€36.00 TTC
(30,00 € HT)
(30,00 € HT)
Grease cover on lower wishbone chassis side - Ford Vedette
Silent block fitted to the lower wishbone axes - Reference Ford 3194 - 4 per vehicle - Sold individually - (18112)
€21.60 TTC
(18,00 € HT)
(18,00 € HT)
Steering relay - Ford vedette - Vendôme - Comet
Steering relay attached to the passenger side chassis. Remember to replace the tie rod with the 2 rotation nuts to remove wear clearances.
€236.00 TTC
(236,00 € HT)
(236,00 € HT)
Ring x 2 - gearbox lever or column foot - Ford Vedette and derivatives
Set of 2 repair rings to replace the silent blocks of the gearbox levers or those at the bottom of the column - Ford Vedette and derivatives.Requires 2 sets per vehicle
€32.00 TTC
(32,00 € HT)
(32,00 € HT)
