Ford Vedette spinnaker seal ring
Sealing ring with steel strapping (metallic spinnaker seal) placed on the Ford Vedette bridge nose.
(26,19 € HT)
Steering relay - Ford vedette - Vendôme - Comet
Steering relay attached to the passenger side chassis. Remember to replace the tie rod with the 2 rotation nuts to remove wear clearances.
(236,00 € HT)
Rear hub oil seal Ford Vedette Vendome Comete
Rear drum sealing ring - (Non contractual photo)
(25,00 € HT)
Ford Vedette gearbox primary shaft groove bearing
Bearing 40x80x18 with locking groove, special Ford Vedette gearbox
(45,67 € HT)
Drive shaft spacers - Ford Vedette
Drive shaft spider. 2 per tree - Sold individually.
(50,00 € HT)
Ford Vedette rear suspension blade bush
" Silent block to be mounted in the eyelets of the rear suspension blades - 6 pieces per suspension (or 12 on a vehicle) - Sold individually D int = 12 mm D ext = 20.5 mm approximately D ext with collar = 30 mm Long without collar = 22 mm "
(13,50 € HT)
Ford Vedette gearbox outlet seal ring
Sealing ring (oil seal) placed at the Ford Vedette gearbox outlet.
(14,17 € HT)
Gearbox or axle oil SAE 80-140 - IGOL - 1L
Viscosity index 80 - 140API GL-4(Not suitable for Peugeot type screw axles)
(20,00 € HT)
Grease cover on lower triangle wheel side - Ford Vedette
Rubber ring for Ford Vedette front axle - on lower pivot - 4 per vehicle - Sold individually Ford Ref = 3193
(16,00 € HT)
Tie rod ends - Ford Vedette
Set of steering ball joints for Ford Vedette 1949 to 54, Abeille, Vendôme, Comète, Monte Carlo.Includes:- 1 x long ball joint,- 1 x short ball joint.(the adjusting sleeve is not supplied)
(176,00 € HT)
Ford Vedette stabilizer bar support
Mounting bracket for stabilizer bar. 2 per vehicle - Sold individually.
(26,50 € HT)
Etoquiau - central blade fixing - Ford Vedette Vendome Comete monte Carlo
(64,00 € HT)
Ford Vedette gearbox inlet seal ring
Sealing ring (oil seal) placed at the Ford Vedette gearbox outlet.35 x 51
(14,17 € HT)
Ford Vedette stabilizer bar bush
Silent block for Ford Vedette stabilizer bar - 4 per side or 8 for a vehicle - Sold individually.
(13,00 € HT)
Upper and lower adjustment for Ford vedette front hub
Allows adjustment of the camber on the front axle. When these parts are worn, play appears making it impossible to adjust the geometry of the front axle and making the vehicle's driving imprecise.Sold individually (2 per front hub)
(96,00 € HT)
Kit 2 x Ford Vedette pivots
" Ford Vedette front pivot repair kit for all models, Bee, Comet, Monte Carlo, Vendôme. Includes 2 pins and 4 bronze bushings. (for 2 wheels). The 2 axes are in treated steel for a much greater hardness than ordinary commercial products. ...
(240,00 € HT)
Viewed products
Master cylinder outlet connection with banjo
MASTER CYLINDER OUTLET CONNECTION WITH BANJOBolt M1 / 2 * 20F-F7 / 16 * 20FBanjo D15 F3 / 8 * 24F 84 °
(34,00 € HT)

Brake hose 430 mm SUMB Marmon
Brake hose Length 430 mm. Entry 7/16 e 16 f / p for SUMB Marmon. Please check the correspondence with your model before ordering.For other models, please call us
(36,00 € HT)
Exhaust Presidence - n2 - stainless steel primary tube - Simca Presidence
Primary tube between the "Y" and the silencer - Part 2 on the photoAll stainless steel.
(102,00 € HT)

Simca V8 cylinder head screw set
Set of 34 black phosphated hexagonal head screws - 2 screw lengths in the set. Resists up to 6 m.kg
(155,20 € HT)
Solenoid coil Rushmatic Simca Chambord Presidence
12v solenoid type actuator for Rushmatic. Supplied with connection wire, central rod and dust cover. Mounted on Rushmatic Simca (Rush-Matic)
(170,00 € HT)
Rear brake cylinder 34.9mm - SUMB Marmon
For Simca SUMB Marmon and other heavy-duty derivatives.Complete rear wheel cylinder 1'3 / 8 (34.93 mm).
(120,00 € HT)

Master cylinder Panhard PL 17 and 24
Master cylinder for Panhard Pl 17 and 24 - diam 22 mm. French made
(76,00 € HT)

Exhaust Presidence - n1 - stainless steel Y tube - Simca Presidence
Stainless steel exhaust - Y - connecting the 2 cast iron manifolds to the line.Part n ° 1 on the photo
(380,00 € HT)
