Central intake gasket - Ford Vedette
Central gasket intake housing for Vedette Ford. Special model for small Ford V8. Attention does not suit the V8 Simca Versailles -Chambord
(50,00 € HT)
Echappement joint extremite bloc V8 Ford Vedette et Simca
" Exhaust gasket, engine block outlet, small model placed at the ends. 4 on one engine - Sold individually. "
(6,00 € HT)
Ignition coil 6V - High Performance
Bosch, NGK or Béru High Performance type ignition coil, guaranteed for use with:- 6 V platinum-plated screw igniter (breakers),- electronic ignition type 123 ignition,- platinum screw igniter + electronic amplification module
(70,00 € HT)
Exhaust kit 8 seals Ford Vedette and Simca Versailles Chambord
" Assortment of 8 exhaust gaskets for an engine. Either: 2 central manifold joints on block 4 manifold outer joints on block 2 manifold outlet seals to 2 in 1 tube. "
(57,92 € HT)
Head gasket 2 mm solid copper Ford Vedette
Solid copper cylinder head gasket. 2mm thickness. Used with planed cylinder head. Tightening to 5m.kg. Mandatory installation with aerosol sealant, available here a>. Measured cylinder head thickness Head gasket type 37.3 mm ...
(160,40 € HT)
Head ignition for RB Ducellier Ford starter Simca Versailles
Head for RB Ducellier distributor, distributor mounted on V8 Simca Versailles, Chambord etc. Can also be mounted on Marmon with petrol V8 equipped with civilian ignition.
(46,00 € HT)
Ducellier 618509 carbon brushes for Ford Vedette starter motor
Ducellier 618509 carbon brushes for Ford Vedette starter motor
(32,50 € HT)
Pellet - set of 4 - Ford Vedette cylinder heads
Set of 4 18.4 mm pellets for Ford Vedette cylinder heads
(28,00 € HT)
IGOL 20W50 mineral oil - 5L can
5 l can (non contractual photo) - Viscosity: 20W-50BenefitsHéRITAGE GTZ mineral oil.Multigrade lubricant for Gasoline and Diesel engines, made from severely refined mineral bases and additives suitable for older engines. The anti-wear additive ...
(30,00 € HT)
Pressure hose for igniter Ø 5.5 mm - by the meter
Hose to connect the igniter / carburetor depression 5.5 mm sold by the meter.
(8,50 € HT)
Ford Vedette bearings - 010 - 53.04 mm
Set of bearings for Vedette Ford 1949 -54 engine. (1 rear flanged bearing + 2 front and central single bearings) Dimension: .010 US (i.e. + / - 0.25 mm)
(765,00 € HT)
Rod bearings Ford Vedette 53-54 or Simca Chambord - 030 - 43.83 mm
" Set of bearings (16 half-shells) for Ford Vedette 2nd generation 1953-54 and Simca V8 engines. Dimension: .030 US (0.75 mm) Each connecting rod receives its pair of bearings. "
(420,00 € HT)
Fuel gauge - replacement float
Float in synthetic material resistant to current fuels. Used to replace the cork floats on the fuel gauge Length: 1.40" Diameter: 1.14"
(17,72 € HT)
Reinforced 90 mm exhaust mounting strap
Suspension strap for exhaust. Robust construction, reinforced rubber, metal eyelets.92 mm center distance for M8 mm screws.
(13,48 € HT)
Water pump repair kit with aluminum impeller - Ford Vedette
Repair kit for water pump for "Y" or "T" pump body - years 1949-54. New axle is 16mm instead of 12 mm. So you need to drill body 16.5 mm. We recommend correcting the seat of the rotating joint at the back of the body.
(151,20 € HT)