Standard 6V coil ignition
Branded ignition coil guaranteed for use with 6 V platinum-plated igniter (breakers). Impedance respected to prevent the breakers from becoming blue. Also works perfectly with electronic module or integral electronic igniter.
(45,00 € HT)
Engine cover gasket for Ford Vedette
Engine gaskets kit (French manufacture) including:2 cylinder head gaskets with a copper face - thickness 1.6 mm1 gasket under central intake housing8 gaskets for exhaust manifold (6 block side - 2 at manifold outlet)1 oil filter foot gasket1 oil ...
(275,00 € HT)
Set of 8 pistons 66.50 Ford Vedette
Set of 8 pistons - New manufacture, similar to the original model - reduction in piston mass (approximately 255 gr with rings) - molybdenum treatment - cylinder dimension 66.50 mm. Supplied with segments, pins and circlips - The segments supplied ...
(1 290,00 € HT)
Set of 8 pistons 66.04 Ford Vedette
Set of 8 pistons - New manufacture, similar to the original model - reduction in piston mass (approximately 255 gr with rings) - molybdenum treatment - cylinder dimension 66.04 mm. Supplied with segments, pins and circlips - The segments supplied ...
(1 290,00 € HT)
Bearing 6203 - 17x40x12
Bearing - 17x40x12 waterproof (often used on dynamo, water pump, flywheel center, etc.). Check with the dimensions of your bearing.
(9,00 € HT)
Ford Vedette disc clutch
Clutch disc reconditioned, in standard exchange for Ford Vedette. Complete disassembly, micro balling and painting. (The sending is done after receipt of the used mechanism, not destroyed)(Depending on the year, non-contractual photo)
(120,00 € HT)

Ducellier 618509 carbon brushes for Ford Vedette starter motor
Ducellier 618509 carbon brushes for Ford Vedette starter motor
(32,50 € HT)
Ford Vedette bearings - 020 - 52.79 mm
" Bearing set for Ford Vedette engine 1949 -54. (1 rear flange bearing + 2 front and central single bearings) Dimension: .020 US (0.50 mm) "
(697,50 € HT)
Ford Vedette exhaust valve
Ford Vedette exhaust valve, flared tail, rectified used.
(66,40 € HT)
Fuel gauge - replacement plastic float
White plastic float. Used to replace ring gauge floats.
(12,50 € HT)
Ford Featured Intake Valve
Ford Vedette intake valve, flared tail, rectified occasion. 33.63 x 110 x 6.86 mm
(62,20 € HT)
Ford Vedette Stromberg 22.2 Carburetor Kit
Overhaul kit for Stromberg 22.2 (2x30 mm) carburetor. Delivered with complete recovery pump. Fitting on Ford Vedette.
(81,60 € HT)
Fuel pump - 6V or 12V control push button
6 or 12v 10A push button. Can be used to activate an electric fuel pump for a few seconds, for example.
(8,25 € HT)
Water pump repair kit with aluminum impeller - Ford Vedette
Repair kit for water pump for "Y" or "T" pump body - years 1949-54. New axle is 16mm instead of 12 mm. So you need to drill body 16.5 mm. We recommend correcting the seat of the rotating joint at the back of the body.
(151,20 € HT)
Fuel pump - GUIOT diaphragm kit Ø90mm - Ford Vedette Simca
Replacement diaphragm for GUIOT fuel pump (Vedette Ford and Simca engine). Diam 90mm. Supplied with membrane and gaskets. (check the type of pump before ordering)
(25,00 € HT)
Viewed products
0.25mm connecting rod bearings - Ø 40mm - Simca 8 - 1200 cm3
connecting rod bearing 0.25 - Ø 40mm - Simca 8 - 1200 cm3
(255,00 € HT)
conrod bearing STD - Ø 44 - FLASH - RUSH 7CV - RUSH SUPER M - Simca Aronde Ariane and 1300 1301
Set of bearings for connecting rods STD dimension - Ø 44Mounts on engine type 312 -316 -FLASH - RUSH 7CV - RUSH SUPER MFor vehicle:- Dovetail motor FLASH or RUSH 7hp,- Ariane with RUSH and RUSH Super M engines,- SIMCA 1300 and 1301(Not suitable ...
(202,00 € HT)
Clutch mechanism type 3 - Simca 8 - 9 - Aronde P60
Clutch mechanism reconditioned, in standard exchange.Complete disassembly, micro balling, surfacing and retaring of the pressure plate.(The sending is done after receipt of the used mechanism, not destroyed - Depending on the year, ...
(230,00 € HT)
