Head gasket 3 mm solid copper Ford Vedette
Solid copper cylinder head gasket. Thickness 3mm. Used with very planed cylinder head.Tightening at 5m.kg. Pose impérative avec le produit d'étanchéité en pâte pour les joint de culasse 2 ou 3 mm disponible ici.Cylinder head thickness measured ...
€192.40 TTC
(192,40 € HT)
(192,40 € HT)
Ford Vedette and Simca Versailles Chambord braid set
" Set of braids for crankshaft Vedette Ford and Simca Aquilon engine (rear bearing and front bearing) Versailles, Chambord etc ... New product, of very high technical quality. Mounts with ease, cuts easily with a cuter leaving 1 to 2 mm ...
€49.90 TTC
(41,58 € HT)
(41,58 € HT)
Bearing 6203 - 17x40x12
Bearing - 17x40x12 waterproof (often used on dynamo, water pump, flywheel center, etc.). Check with the dimensions of your bearing.
€10.80 TTC
(9,00 € HT)
(9,00 € HT)
Ford Vedette bearings - 030 - 52.54 mm
" Bearing set for Ford Vedette engine 1949 -54. (1 rear flange bearing + 2 front and central single bearings) Dimension: .030 US (0.75 mm) "
€810.00 TTC
(675,00 € HT)
(675,00 € HT)
Aviation collex type paste gasket for cylinder head - 450ml
Sealing paste to be applied on both sides of a cylinder head gasket. Product similar to "Collex". Leave to evaporate for about 30 min at room temperature after application, then fit the gasket - improves the seal - recommended with solid copper ...
€42.00 TTC
(35,00 € HT)
(35,00 € HT)
Pellet - set of 4 - Ford Vedette cylinder heads
Set of 4 18.4 mm pellets for Ford Vedette cylinder heads
€43.00 TTC
(43,00 € HT)
(43,00 € HT)
Ford Vedette oil pump pinion
Replacement gear for oil pump - V8 Ford Vedette. Supplied with 4 rivets. (Advantageously replaces the celoron one that has become fragile over time)Attention for the V8 Simca 13 hp 2350 cm3, choose the reference "Simca oil pump pinion" on our shop.
€187.00 TTC
(187,00 € HT)
(187,00 € HT)
Aluminum water departure on engine block - Ford star
Aluminum water supply on engine block to radiator - Ford Vedette 1949 to 1954 and Comète 13 hpCareful French manufacturing - machined and welded aluminum.Two parts are needed per engine. Sold individually.
€91.80 TTC
(91,80 € HT)
(91,80 € HT)
Standard 6V coil ignition
Branded ignition coil guaranteed for use with 6 V platinum-plated igniter (breakers). Impedance respected to prevent the breakers from becoming blue. Also works perfectly with electronic module or integral electronic igniter.
€43.20 TTC
(36,00 € HT)
(36,00 € HT)
Exhaust - outlet tube + stainless steel stock - Ford Vedette
" Outlet tube with crosshead (bridge passage) to be connected to the silencer outlet. Ford Vedette 1949 to 1954. All stainless steel. "
€426.00 TTC
(355,00 € HT)
(355,00 € HT)
Head gasket 1.6 mm Ford Vedette standard
" Cylinder head gasket for Ford Vedette 1949 to 1954. One side all copper, the other with copper hems, thickness 1.6 mm approximately Measured cylinder head thickness Head gasket type 37.3 mm (original) 1.6 mm standard gasket from 37.0 ...
€90.00 TTC
(75,00 € HT)
(75,00 € HT)
bearing stops - Ford 1949 to 52
Set of 4 retainers for V8 Ford Vedette 1949 - 52 (Strainer with spring and support on central bearing)
€20.34 TTC
(20,34 € HT)
(20,34 € HT)
Oil seal rings gearbox lever - Simca Versailles Chambord
Set of 2 sealing rings (oil seal) for gearbox controls (mounted on control cover).Gaskets to be glued to immobilize them.
€14.40 TTC
(12,00 € HT)
(12,00 € HT)
Set of 8 pistons 67.00 Ford Vedette
Set of 8 pistons - New manufacture, similar to the original model - reduction in piston mass (approx. 255 gr with segments) - molybdenum treatment - cylinder dimension 67.00 mm. Supplied with segments, pins and circlips - The segments supplied ...
€1,548.00 TTC
(1 290,00 € HT)
(1 290,00 € HT)
Viewed products
Regulator converter 12v to 6V for wiper motor
€66.00 TTC
(55,00 € HT)
(55,00 € HT)
Ford Vedette bearings - 020 - 52.79 mm
" Bearing set for Ford Vedette engine 1949 -54. (1 rear flange bearing + 2 front and central single bearings) Dimension: .020 US (0.50 mm) "
€810.00 TTC
(675,00 € HT)
(675,00 € HT)
