Head gasket 2 mm solid copper Ford Vedette
Solid copper cylinder head gasket. 2mm thickness. Used with planed cylinder head. Tightening to 5m.kg. Mandatory installation with aerosol sealant, available here a>. Measured cylinder head thickness Head gasket type 37.3 mm ...
€117.40 TTC
(117,40 € HT)
(117,40 € HT)
Fuel gauge - replacement float
Float in synthetic material resistant to current fuels. Used to replace the cork floats on the fuel gauge Length: 1.40" Diameter: 1.14"
€17.72 TTC
(17,72 € HT)
(17,72 € HT)
Standard 6V coil ignition
Branded ignition coil guaranteed for use with 6 V platinum-plated igniter (breakers). Impedance respected to prevent the breakers from becoming blue. Also works perfectly with electronic module or integral electronic igniter.
€33.00 TTC
(33,00 € HT)
(33,00 € HT)
Bearing 6203 - 17x40x12
Bearing - 17x40x12 waterproof (often used on dynamo, water pump, flywheel center, etc.). Check with the dimensions of your bearing.
€8.19 TTC
(8,19 € HT)
(8,19 € HT)
Exhaust kit 8 seals Ford Vedette and Simca Versailles Chambord
" Assortment of 8 exhaust gaskets for an engine. Either: 2 central manifold joints on block 4 manifold outer joints on block 2 manifold outlet seals to 2 in 1 tube. "
€57.92 TTC
(57,92 € HT)
(57,92 € HT)
Metal body battery switch - safety
Coupe batterie - permet d'isoler électriquement la batterie.
€22.50 TTC
(22,50 € HT)
(22,50 € HT)
Carburetor gasket Stromberg Ford Vedette
Gasket for 22.2 Stromberg carburettor
€16.50 TTC
(16,50 € HT)
(16,50 € HT)
Set of 8 pistons 66.04 Ford Vedette
Set of 8 pistons - New manufacture, similar to the original model - reduction in piston mass (approximately 255 gr with rings) - molybdenum treatment - cylinder dimension 66.04 mm. Supplied with segments, pins and circlips - The segments supplied ...
€1,132.50 TTC
(1 132,50 € HT)
(1 132,50 € HT)
Ford Vedette and Simca Versailles Chambord braid set
" Set of braids for crankshaft Vedette Ford and Simca Aquilon engine (rear bearing and front bearing) Versailles, Chambord etc ... New product, of very high technical quality. Mounts with ease, cuts easily with a cuter leaving 1 to 2 mm ...
€41.58 TTC
(41,58 € HT)
(41,58 € HT)
Reinforced collar for exhaust - Ø 52-55 mm
Reinforced collar for exhaust - Ø 52.55 mmRobust French manufacturing
€5.42 TTC
(5,42 € HT)
(5,42 € HT)
Set of 8 pistons 66.50 Ford Vedette
Set of 8 pistons - New manufacture, similar to the original model - reduction in piston mass (approximately 255 gr with rings) - molybdenum treatment - cylinder dimension 66.50 mm. Supplied with segments, pins and circlips - The segments supplied ...
€1,132.50 TTC
(1 132,50 € HT)
(1 132,50 € HT)
Ford Vedette exhaust valve
Ford Vedette exhaust valve, flared tail, rectified used.
€66.40 TTC
(66,40 € HT)
(66,40 € HT)
Calibrouge (Plastigage) mechanical clearance measurement
"Plastigage"The Calibrouge ("plastigage or plastigauge") is a simple and practical tool for measuring the clearances of your bearings. Range of use: operating clearance from 0.025 to 0.175 mm
€22.50 TTC
(22,50 € HT)
(22,50 € HT)
Disc set of 2 - upper block approx Ø 25 mm Simca
Set of 2 tablets for Simca engine block. Mounting on the surface plane: approximately 25.9 mm. Simca Trianon, Versailles, Régence, Beaulieu, Chambord, Présidence, Marly 1 et2, Ariane 8
€23.60 TTC
(23,60 € HT)
(23,60 € HT)
