Set of custom 4-groove piston rings Ford or Simca V8
Set of segments for V8 Ford Vedette, Vendôme, Simca Trianon, Versailles, Régence, Beaulieu, Chambord, Présidence, Marly 1 and 2, Ariane 8.For 4-groove piston, all dimensions, do not hesitate to contact us 033 4 42 57 79 06 for estimate.(Price ...
€336.00 TTC
(280,00 € HT)
(280,00 € HT)
Set of 8 pistons 67.50 Ford Vedette
Set of 8 pistons - New manufacture, similar to the original model - reduction in piston mass (approximately 255 gr with rings) - molybdenum treatment - cylinder size 67.50 mm. Supplied with segments, pins and circlips - The segments supplied are ...
€1,548.00 TTC
(1 290,00 € HT)
(1 290,00 € HT)
Pressure hose for igniter Ø 5.5 mm - by the meter
Hose to connect the igniter / carburetor depression 5.5 mm sold by the meter.
€10.20 TTC
(8,50 € HT)
(8,50 € HT)
Bearing 6203 - 17x40x12
Bearing - 17x40x12 waterproof (often used on dynamo, water pump, flywheel center, etc.). Check with the dimensions of your bearing.
€10.80 TTC
(9,00 € HT)
(9,00 € HT)
160 mm float fuel gauge - 6V
" Float fuel gauge. Adaptable model. Arm length approx. 160 mm. External diameter of plate 54 mm - fixing center distance 38 mm. Supplied with cork seal. 3-hole fixing. Internal resistance approx. 110 ohms. For 6-volt vehicle only. "
€48.00 TTC
(40,00 € HT)
(40,00 € HT)
Clutch mechanism Ford Vedette
Clutch mechanism reconditioned, in standard exchange mounted on Ford Vedette, Abeille, Comète, Monte Carlo, Vendôme engine Complete disassembly, micro balling, surfacing and retaring of the pressure plate. (The sending is done after receipt ...
€354.00 TTC
(295,00 € HT)
(295,00 € HT)
Ford Vedette water pump belt
Main belt connecting water pumps-crankshaft-fan
€24.00 TTC
(20,00 € HT)
(20,00 € HT)
Electronic regulator for 6V negative ground dynamo
Electronic regulator for 6V negative ground dynamo - Original appearance in ED3 housing.For dynamos with positive excitation.Charge stabilization at 7.4V. Brighter lighting, better battery charge quality, improved ignition voltage.(Exchange standard)
€208.00 TTC
(208,00 € HT)
(208,00 € HT)
Ford Vedette gearbox outlet seal ring
Sealing ring (oil seal) placed at the Ford Vedette gearbox outlet.
€17.00 TTC
(14,17 € HT)
(14,17 € HT)
Reinforced collar for exhaust - Ø 44-47 mm
Reinforced collar for exhaust - Ø 44-47 mmRobust French manufacturing
€5.80 TTC
(4,83 € HT)
(4,83 € HT)
Ford Vedette Stromberg 22.2 Carburetor Kit
Overhaul kit for Stromberg 22.2 (2x30 mm) carburetor. Delivered with complete recovery pump. Fitting on Ford Vedette.
€97.92 TTC
(81,60 € HT)
(81,60 € HT)
Ford Vedette bearings - 020 - 52.79 mm
" Bearing set for Ford Vedette engine 1949 -54. (1 rear flange bearing + 2 front and central single bearings) Dimension: .020 US (0.50 mm) "
€837.00 TTC
(697,50 € HT)
(697,50 € HT)
Standard 6V coil ignition
Branded ignition coil guaranteed for use with 6 V platinum-plated igniter (breakers). Impedance respected to prevent the breakers from becoming blue. Also works perfectly with electronic module or integral electronic igniter.
€54.00 TTC
(45,00 € HT)
(45,00 € HT)
Exhaust kit 8 seals Ford Vedette and Simca Versailles Chambord
" Assortment of 8 exhaust gaskets for an engine. Either: 2 central manifold joints on block 4 manifold outer joints on block 2 manifold outlet seals to 2 in 1 tube. "
€69.50 TTC
(57,92 € HT)
(57,92 € HT)
