Ford Vedette disc clutch
Clutch disc reconditioned, in standard exchange for Ford Vedette. Complete disassembly, micro balling and painting. (The sending is done after receipt of the used mechanism, not destroyed)(Depending on the year, non-contractual photo)
€144.00 TTC
(120,00 € HT)
(120,00 € HT)
Engine paint oxide green RAL 6020 - 500 ml
Engine paint oxide green RAL 6020 -Pot of 500 mlSuitable for engines, housings, gearboxes, differentials, brake drums and all parts subject to heating in cast iron, steel and light alloys.Direct application on degreased metal (or better, treated ...
€40.80 TTC
(34,00 € HT)
(34,00 € HT)
Rod bearings Ford Vedette 53-54 or Simca Chambord - 040 - 43.57 mm
" Set of bearings (16 half-shells) for Ford Vedette 2nd generation 1953-54 and Simca V8 engines. Dimension: .040 US (1 mm) Each connecting rod receives its pair of bearings. "
€468.00 TTC
(390,00 € HT)
(390,00 € HT)
Echappement joint extremite bloc V8 Ford Vedette et Simca
" Exhaust gasket, engine block outlet, small model placed at the ends. 4 on one engine - Sold individually. "
€7.20 TTC
(6,00 € HT)
(6,00 € HT)
Fuel gauge - replacement plastic float
White plastic float. Used to replace ring gauge floats.
€15.00 TTC
(12,50 € HT)
(12,50 € HT)
Exhaust - outlet tube + stainless steel stock - Ford Vedette
" Outlet tube with crosshead (bridge passage) to be connected to the silencer outlet. Ford Vedette 1949 to 1954. All stainless steel. "
€404.82 TTC
(337,35 € HT)
(337,35 € HT)
3-finger clutch - 9CF12 - Ford Vedette 1949-52
Clutch mechanism reconditioned, in standard exchange mounted on Ford Vedette, Abeille, Comète, Monte Carlo, Vendôme engineComplete disassembly, micro balling, surfacing and retaring of the pressure plate.(The sending is done after receipt of the ...
€538.80 TTC
(449,00 € HT)
(449,00 € HT)
Set of 2 Ford Vedette front engine mounts
" Set of 2 front supports for V8 Ford Vedette. Fixing center distance to be slightly modified. "
€39.60 TTC
(33,00 € HT)
(33,00 € HT)
Calibrouge (Plastigage) mechanical clearance measurement
"Plastigage"The Calibrouge ("plastigage or plastigauge") is a simple and practical tool for measuring the clearances of your bearings. Range of use: operating clearance from 0.025 to 0.175 mm
€27.00 TTC
(22,50 € HT)
(22,50 € HT)
12V electric fuel pump
" 12V electric fuel pump. Connects in series with the original fuel line. Keeps the hand pump. Avoids having to lift the hood to turn up gasoline before starting. To be powered through a push button for occasional operation. Low pressure, no need ...
€66.00 TTC
(55,00 € HT)
(55,00 € HT)
Bearing 6203 - 17x40x12
Bearing - 17x40x12 waterproof (often used on dynamo, water pump, flywheel center, etc.). Check with the dimensions of your bearing.
€10.80 TTC
(9,00 € HT)
(9,00 € HT)
Ford Vedette 54 disc clutch 215 mm
Clutch disc reconditioned, in standard exchange for Ford Vedette. Complete disassembly, micro balling and painting. (The sending is done after receipt of the used mechanism, not destroyed)(Depending on the year, non-contractual photo)
€144.00 TTC
(120,00 € HT)
(120,00 € HT)
160 mm float fuel gauge - 6V
" Float fuel gauge. Adaptable model. Arm length approx. 160 mm. External diameter of plate 54 mm - fixing center distance 38 mm. Supplied with cork seal. 3-hole fixing. Internal resistance approx. 110 ohms. For 6-volt vehicle only. "
€48.00 TTC
(40,00 € HT)
(40,00 € HT)
Ignition coil 12v VALEO
Ignition coil guaranteed for use with a 12 V platinum screw igniter (breakers). Impedance respected to prevent the breakers from bluing.Works perfectly also with electronic module or integral electronic igniter. (Non contractual photo)
€57.60 TTC
(48,00 € HT)
(48,00 € HT)
Set of 8 pistons 67.50 Ford Vedette
Set of 8 pistons - New manufacture, similar to the original model - reduction in piston mass (approximately 255 gr with rings) - molybdenum treatment - cylinder size 67.50 mm. Supplied with segments, pins and circlips - The segments supplied are ...
€1,548.00 TTC
(1 290,00 € HT)
(1 290,00 € HT)
