Central intake gasket - Ford Vedette
Central gasket intake housing for Vedette Ford. Special model for small Ford V8. Attention does not suit the V8 Simca Versailles -Chambord
€60.00 TTC
(50,00 € HT)
(50,00 € HT)
Ford Vedette bearings - 030 - 52.54 mm
" Bearing set for Ford Vedette engine 1949 -54. (1 rear flange bearing + 2 front and central single bearings) Dimension: .030 US (0.75 mm) "
€810.00 TTC
(675,00 € HT)
(675,00 € HT)
Ford Vedette disc clutch
Clutch disc reconditioned, in standard exchange for Ford Vedette. Complete disassembly, micro balling and painting. (The sending is done after receipt of the used mechanism, not destroyed)(Depending on the year, non-contractual photo)
€144.00 TTC
(120,00 € HT)
(120,00 € HT)
160 mm float fuel gauge - 6V
" Float fuel gauge. Adaptable model. Arm length approx. 160 mm. External diameter of plate 54 mm - fixing center distance 38 mm. Supplied with cork seal. 3-hole fixing. Internal resistance approx. 110 ohms. For 6-volt vehicle only. "
€48.00 TTC
(40,00 € HT)
(40,00 € HT)
Engine paint black RAL 9005 - 500 ml
Black paint - 500 ml jarSuitable for engines, housings, gearboxes, differentials, brake drums and all parts subject to heating in cast iron, steel and light alloys.Direct application on degreased metal (or better, treated with our Phosprim 4090), ...
€40.80 TTC
(34,00 € HT)
(34,00 € HT)
Aviation collex type paste gasket for cylinder head - 117ml
Sealing paste to be applied on both sides of a cylinder head gasket. Product similar to "Collex". Leave to evaporate for about 30 min at room temperature after application, then fit the gasket - improves the seal - recommended with solid copper ...
€27.60 TTC
(23,00 € HT)
(23,00 € HT)
Ford 53 and 54 crankshaft bearing screws
Set of bearing screws for V8 Ford Vedette model 1953 and 1954
€134.42 TTC
(134,42 € HT)
(134,42 € HT)
Ford Vedette and Simca Versailles Chambord braid set
" Set of braids for crankshaft Vedette Ford and Simca Aquilon engine (rear bearing and front bearing) Versailles, Chambord etc ... New product, of very high technical quality. Mounts with ease, cuts easily with a cuter leaving 1 to 2 mm ...
€49.90 TTC
(41,58 € HT)
(41,58 € HT)
Disc set of 2 - upper block approx Ø 25 mm Simca
Set of 2 tablets for Simca engine block. Mounting on the surface plane: approximately 25.9 mm. Simca Trianon, Versailles, Régence, Beaulieu, Chambord, Présidence, Marly 1 et2, Ariane 8
€17.00 TTC
(17,00 € HT)
(17,00 € HT)
Ford Vedette Stromberg 22.2 Carburetor Kit
Overhaul kit for Stromberg 22.2 (2x30 mm) carburetor. Delivered with complete recovery pump. Fitting on Ford Vedette.
€96.00 TTC
(80,00 € HT)
(80,00 € HT)
Accelerator pump kit for Stromberg 22.2 Ford Vedette carburettor
Accelerator pump kit for Stromberg 22.2 carburettor. Fitting on Ford Vedette.
€36.00 TTC
(30,00 € HT)
(30,00 € HT)
Oil pressure contact mano - Ford Vedette 1949 - 54
oil pressure switch for Ford Vedette engine from 1949 to 1954 - Thread M 10x100
€12.60 TTC
(10,50 € HT)
(10,50 € HT)
Exhaust - outlet tube + stainless steel stock - Ford Vedette
" Outlet tube with crosshead (bridge passage) to be connected to the silencer outlet. Ford Vedette 1949 to 1954. All stainless steel. "
€426.00 TTC
(355,00 € HT)
(355,00 € HT)
6V electric fuel pump
6V electric fuel pump. To be connected to the ignition coil power supply. Connects in series with the original fuel line.Allows you to keep the manual pump. Avoids having to lift the hood to turn up gasoline before starting.Is intended to remain ...
€90.00 TTC
(75,00 € HT)
(75,00 € HT)
Kit of 12V electric fuel pump
" 12V electric fuel pump. Connects in series with the original fuel line. Keeps the hand pump. Avoids having to lift the hood to turn up gasoline before starting. To be powered through a push button for occasional operation. Low pressure, no need ...
€96.00 TTC
(80,00 € HT)
(80,00 € HT)
