Pressure hose for igniter Ø 5.5 mm - by the meter
Hose to connect the igniter / carburetor depression 5.5 mm sold by the meter.
€10.20 TTC
(8,50 € HT)
(8,50 € HT)
Ford Vedette and Simca Versailles Chambord braid set
" Set of braids for crankshaft Vedette Ford and Simca Aquilon engine (rear bearing and front bearing) Versailles, Chambord etc ... New product, of very high technical quality. Mounts with ease, cuts easily with a cuter leaving 1 to 2 mm ...
€49.90 TTC
(41,58 € HT)
(41,58 € HT)
160 mm float fuel gauge - 6V
" Float fuel gauge. Adaptable model. Arm length approx. 160 mm. External diameter of plate 54 mm - fixing center distance 38 mm. Supplied with cork seal. 3-hole fixing. Internal resistance approx. 110 ohms. For 6-volt vehicle only. "
€48.00 TTC
(40,00 € HT)
(40,00 € HT)
IGOL Rallye Gear axle transmission oil SAE 75 80 90 - GL4
Oil for gearbox and bridge for old mechanics. Type SAE 75 80 90 - GL4. 1L container.(Not suitable for Peugeot type screw axles)
€18.00 TTC
(15,00 € HT)
(15,00 € HT)
Ignition harness V8 Ford Vedette Simca Versailles Chambord
High performance ignition harness, black silicone, interference suppression in accordance with European legislation. Lengths specially adapted for Ford Vedette, Bee V8 engines; Vendôme, Comète, Monte Carlo and Simca Trianon, Versailles, Régence, ...
€83.95 TTC
(69,96 € HT)
(69,96 € HT)
Reinforced collar for exhaust - Ø 44-47 mm
Reinforced collar for exhaust - Ø 44-47 mmRobust French manufacturing
€5.80 TTC
(4,83 € HT)
(4,83 € HT)
Fuel pump - GUIOT diaphragm kit Ø90mm - Ford Vedette Simca
Replacement diaphragm for GUIOT fuel pump (Vedette Ford and Simca engine). Diam 90mm. Supplied with membrane and gaskets. (check the type of pump before ordering)
€30.00 TTC
(25,00 € HT)
(25,00 € HT)
Calibrouge (Plastigage) mechanical clearance measurement
"Plastigage"The Calibrouge ("plastigage or plastigauge") is a simple and practical tool for measuring the clearances of your bearings. Range of use: operating clearance from 0.025 to 0.175 mm
€27.00 TTC
(22,50 € HT)
(22,50 € HT)
Ignition capacitor 6, 12 and 24V
6.12V and 24V compatible ignition capacitor.
€14.40 TTC
(12,00 € HT)
(12,00 € HT)
Set of piston rings 4 grooves Ø66.04 - 2x2x4x4 - Ford Vedette
Piston ring set Ø 66.04 - for Ford Vedette V8.For piston with 4 grooves, 2x2x4x4. Includes:- 16 compression segments 2 mm high- 16 scraper segments 4mm highNon contractual photo
€336.00 TTC
(280,00 € HT)
(280,00 € HT)
Standard 6V coil ignition
Branded ignition coil guaranteed for use with 6 V platinum-plated igniter (breakers). Impedance respected to prevent the breakers from becoming blue. Also works perfectly with electronic module or integral electronic igniter.
€43.20 TTC
(36,00 € HT)
(36,00 € HT)
Ford Vedette bearings - 030 - 52.54 mm
" Bearing set for Ford Vedette engine 1949 -54. (1 rear flange bearing + 2 front and central single bearings) Dimension: .030 US (0.75 mm) "
€810.00 TTC
(675,00 € HT)
(675,00 € HT)
Bearing 6203 - 17x40x12
Bearing - 17x40x12 waterproof (often used on dynamo, water pump, flywheel center, etc.). Check with the dimensions of your bearing.
€10.80 TTC
(9,00 € HT)
(9,00 € HT)
Disc set of 2 - upper block approx Ø 25 mm Simca
Set of 2 tablets for Simca engine block. Mounting on the surface plane: approximately 25.9 mm. Simca Trianon, Versailles, Régence, Beaulieu, Chambord, Présidence, Marly 1 et2, Ariane 8
€17.00 TTC
(17,00 € HT)
(17,00 € HT)
Exhaust - stainless steel oval silencer - Ford Vedette
Stainless steel silencer for Ford Vedette.
€454.80 TTC
(379,00 € HT)
(379,00 € HT)
