Ford Featured Intake Valve
Ford Vedette intake valve, flared tail, rectified occasion. 33.63 x 110 x 6.86 mm
€62.20 TTC
(62,20 € HT)
(62,20 € HT)
Ford Vedette COTAL disc clutch 215 mm
Clutch disc reconditioned, (exchange) - fit to Ford Vedette. Complete disassembly, micro balling and painting. (The sending is done after receipt of the used mechanism, not destroyed)(Depending on the year, non-contractual photo)
€144.00 TTC
(120,00 € HT)
(120,00 € HT)
160 mm float fuel gauge - 6V
" Float fuel gauge. Adaptable model. Arm length approx. 160 mm. External diameter of plate 54 mm - fixing center distance 38 mm. Supplied with cork seal. 3-hole fixing. Internal resistance approx. 110 ohms. For 6-volt vehicle only. "
€48.00 TTC
(40,00 € HT)
(40,00 € HT)
Ford Vedette bearings - 020 - 52.79 mm
" Bearing set for Ford Vedette engine 1949 -54. (1 rear flange bearing + 2 front and central single bearings) Dimension: .020 US (0.50 mm) "
€810.00 TTC
(675,00 € HT)
(675,00 € HT)
Rod bearings Ford Vedette 53-54 or Simca Chambord - 030 - 43.83 mm
" Set of bearings (16 half-shells) for Ford Vedette 2nd generation 1953-54 and Simca V8 engines. Dimension: .030 US (0.75 mm) Each connecting rod receives its pair of bearings. "
€468.00 TTC
(390,00 € HT)
(390,00 € HT)
Ignition capacitor 6, 12 and 24V
6.12V and 24V compatible ignition capacitor.
€14.40 TTC
(12,00 € HT)
(12,00 € HT)
Set of 8 pistons 66.04 Ford Vedette
Set of 8 pistons - New manufacture, similar to the original model - reduction in piston mass (approximately 255 gr with rings) - molybdenum treatment - cylinder dimension 66.04 mm. Supplied with segments, pins and circlips - The segments supplied ...
€1,548.00 TTC
(1 290,00 € HT)
(1 290,00 € HT)
Aviation collex type paste gasket for cylinder head - 117ml
Sealing paste to be applied on both sides of a cylinder head gasket. Product similar to "Collex". Leave to evaporate for about 30 min at room temperature after application, then fit the gasket - improves the seal - recommended with solid copper ...
€30.00 TTC
(25,00 € HT)
(25,00 € HT)
Fuel pump - GUIOT diaphragm kit Ø90mm - Ford Vedette Simca
Replacement diaphragm for GUIOT fuel pump (Vedette Ford and Simca engine). Diam 90mm. Supplied with membrane and gaskets. (check the type of pump before ordering)
€30.00 TTC
(25,00 € HT)
(25,00 € HT)
Ford Vedette and Simca Versailles Chambord braid set
" Set of braids for crankshaft Vedette Ford and Simca Aquilon engine (rear bearing and front bearing) Versailles, Chambord etc ... New product, of very high technical quality. Mounts with ease, cuts easily with a cuter leaving 1 to 2 mm ...
€49.90 TTC
(41,58 € HT)
(41,58 € HT)
Pellet - set of 4 - Ford Vedette cylinder heads
Set of 4 18.4 mm pellets for Ford Vedette cylinder heads
€43.00 TTC
(43,00 € HT)
(43,00 € HT)
Accelerator pump kit for Stromberg 22.2 Ford Vedette carburettor
Accelerator pump kit for Stromberg 22.2 carburettor. Fitting on Ford Vedette.
€36.00 TTC
(30,00 € HT)
(30,00 € HT)
Reinforced collar for exhaust - Ø 52-55 mm
Reinforced collar for exhaust - Ø 52.55 mmRobust French manufacturing
€6.50 TTC
(5,42 € HT)
(5,42 € HT)
Ignition coil 6V - High Performance
Bosch, NGK or Béru High Performance type ignition coil, guaranteed for use with:- 6 V platinum-plated screw igniter (breakers),- electronic ignition type 123 ignition,- platinum screw igniter + electronic amplification module
€81.60 TTC
(68,00 € HT)
(68,00 € HT)
liner Ø 66.04 - semi finished 65.50 - Simca V8 Versailles Chambord
Liner Ø 66.04 - semi finished 65.50 - long 168mm Ø outside 69 mm Ø flange 70 mm height 5mm - Simca V8 Versailles Chambord - sold individually
€69.80 TTC
(58,17 € HT)
(58,17 € HT)
Exhaust gasket center block V8 Ford Vedette and Simca
Exhaust gasket, engine block outlet (center). 2 per engine - Sold individually.
€7.20 TTC
(6,00 € HT)
(6,00 € HT)
