
Battery switch - safety
Battery isolator - used to electrically isolate the battery. To be placed on a terminal of the battery.
(10,00 € HT)
Reinforced collar for exhaust - Ø 44-47 mm
Reinforced collar for exhaust - Ø 44-47 mmRobust French manufacturing
(4,83 € HT)
Ford Vedette gearbox inlet seal ring
Sealing ring (oil seal) placed at the Ford Vedette gearbox outlet.35 x 51
(14,17 € HT)
Ford Vedette gearbox outlet seal ring
Sealing ring (oil seal) placed at the Ford Vedette gearbox outlet.
(14,17 € HT)
Fuel gauge - replacement float
Float in synthetic material resistant to current fuels. Used to replace the cork floats on the fuel gauge Length: 1.40" Diameter: 1.14"
(17,72 € HT)
Ford Vedette oil pump pinion
Replacement gear for oil pump - V8 Ford Vedette. Supplied with 4 rivets. (Advantageously replaces the celoron one that has become fragile over time)Attention for the V8 Simca 13 hp 2350 cm3, choose the reference "Simca oil pump pinion" on our shop.
(187,00 € HT)

Ford Vedette Stromberg 22.2 Carburetor Kit
Overhaul kit for Stromberg 22.2 (2x30 mm) carburetor. Delivered with complete recovery pump. Fitting on Ford Vedette.
(80,00 € HT)
Standard 6V coil ignition
Branded ignition coil guaranteed for use with 6 V platinum-plated igniter (breakers). Impedance respected to prevent the breakers from becoming blue. Also works perfectly with electronic module or integral electronic igniter.
(36,00 € HT)
Pressure hose for igniter Ø 5.5 mm - by the meter
Hose to connect the igniter / carburetor depression 5.5 mm sold by the meter.
(8,50 € HT)
Set of 8 pistons 67.00 Ford Vedette
Set of 8 pistons - New manufacture, similar to the original model - reduction in piston mass (approx. 255 gr with segments) - molybdenum treatment - cylinder dimension 67.00 mm. Supplied with segments, pins and circlips - The segments supplied ...
(1 290,00 € HT)
Temperature manometer with probe - black background
Mano "OS" temperature indicator (without electrical connection). Direct reading by probe mounted on a radiator hose (high outlet). 52 mm recess on the pressure gauge side.Capillary 1m80. Delivered with lighting and probe for the hose.
(65,00 € HT)
Water pump repair kit with aluminum impeller - Ford Vedette
Repair kit for water pump for "Y" or "T" pump body - years 1949-54. New axle is 16mm instead of 12 mm. So you need to drill body 16.5 mm. We recommend correcting the seat of the rotating joint at the back of the body.
(151,20 € HT)
Clutch mechanism Ford Vedette
Clutch mechanism reconditioned, in standard exchange mounted on Ford Vedette, Abeille, Comète, Monte Carlo, Vendôme engine Complete disassembly, micro balling, surfacing and retaring of the pressure plate. (The sending is done after receipt ...
(262,50 € HT)

Ford Vedette air filter + breather sticker
" Sticker for air filter and breather cap. Mounts on Ford V8 Vedette, Vendôme, Cometer, Monte Carlo etc. Sticker "
(19,26 € HT)
Manometer Tachometer - 2 - 4 - 6 - 8 cyl - electric 12V - ivory background - for negative to mass
Mano "OS" Tachometer 0 to 5000 rpm for 4-cylinder petrol engine. Connects to the "break" terminal on the ignition coil. 52 mm recess on the pressure gauge side. delivered with lighting. for negative to ground
(58,29 € HT)
Rod bearings Ford Vedette 53-54 or Simca Chambord - STD - 44.59 mm
" Set of bearings (16 half-shells) for Ford Vedette 2nd generation 1953-54 and Simca V8 engines. Dimension: STD - 44.59 mm Each connecting rod receives its pair of bearings. "
(390,00 € HT)
Viewed products
4 intake valves 42 x 107.7 x 9 mm - Citroen HY engine ID19
4 intake valves 42 x 107.7 x 9 mm - Citroen HY from 1963 and Citroen DS and ID until 1965
(68,03 € HT)
Piston x 4 Ø 56.50 mm - Citroen Trefle 5cv
Set of 4 pistons Ø 56.50 mm - Citroen Trèfle 5cv
(690,00 € HT)
Silent block for stabilizer bar Ø 16 mm Simca Versailles
Silent block for connection between stabilizer bar and suspension pivot mounted on Simca Trianon, Versailles, Régence and Malry I Stabilizer bar thread in 16 mm - Silent block location diameter = 20.7 mm p > The price allows to redo only ...
(37,40 € HT)