Double pressure gauge holder
Metal support, black lacquered for standard manometer D52 mm. Ready to fix.
€12.00 TTC
(10,00 € HT)
(10,00 € HT)
Reinforced collar for exhaust - Ø 64-67 mm
Reinforced collar for exhaust - Ø 64-67 mmRobust French manufacturing
€7.80 TTC
(6,50 € HT)
(6,50 € HT)
Ford Vedette bearings - 020 - 52.79 mm
" Bearing set for Ford Vedette engine 1949 -54. (1 rear flange bearing + 2 front and central single bearings) Dimension: .020 US (0.50 mm) "
€810.00 TTC
(675,00 € HT)
(675,00 € HT)
Set of 8 pistons 66.04 Ford Vedette
Set of 8 pistons - New manufacture, similar to the original model - reduction in piston mass (approximately 255 gr with rings) - molybdenum treatment - cylinder dimension 66.04 mm. Supplied with segments, pins and circlips - The segments supplied ...
€1,548.00 TTC
(1 290,00 € HT)
(1 290,00 € HT)
Ford Vedette 54 disc clutch 215 mm
Clutch disc reconditioned, in standard exchange for Ford Vedette. Complete disassembly, micro balling and painting. (The sending is done after receipt of the used mechanism, not destroyed)(Depending on the year, non-contractual photo)
€144.00 TTC
(120,00 € HT)
(120,00 € HT)
Ford 53 and 54 crankshaft bearing screws
Set of bearing screws for V8 Ford Vedette model 1953 and 1954
€134.42 TTC
(134,42 € HT)
(134,42 € HT)
Ford Vedette V8 oil filter housing seal
Circular seal for Ford Vedette, Vendôme and Simca Vedette oil filter housing.Can be mounted on a cover or on a base depending on the model and year
€8.96 TTC
(8,96 € HT)
(8,96 € HT)
Aviation collex type paste gasket for cylinder head - 117ml
Sealing paste to be applied on both sides of a cylinder head gasket. Product similar to "Collex". Leave to evaporate for about 30 min at room temperature after application, then fit the gasket - improves the seal - recommended with solid copper ...
€27.60 TTC
(23,00 € HT)
(23,00 € HT)
IGOL Rallye Gear axle transmission oil SAE 75 80 90 - GL4
Oil for gearbox and bridge for old mechanics. Type SAE 75 80 90 - GL4. 1L container.(Not suitable for Peugeot type screw axles)
€18.00 TTC
(15,00 € HT)
(15,00 € HT)
Ignition coil 6V - High Performance
Bosch, NGK or Béru High Performance type ignition coil, guaranteed for use with:- 6 V platinum-plated screw igniter (breakers),- electronic ignition type 123 ignition,- platinum screw igniter + electronic amplification module
€81.60 TTC
(68,00 € HT)
(68,00 € HT)
Reinforced collar for exhaust - Ø 44-47 mm
Reinforced collar for exhaust - Ø 44-47 mmRobust French manufacturing
€5.80 TTC
(4,83 € HT)
(4,83 € HT)
Head gasket 1.6 mm Ford Vedette standard
" Cylinder head gasket for Ford Vedette 1949 to 1954. One side all copper, the other with copper hems, thickness 1.6 mm approximately Measured cylinder head thickness Head gasket type 37.3 mm (original) 1.6 mm standard gasket from 37.0 ...
€90.00 TTC
(75,00 € HT)
(75,00 € HT)
12V electric fuel pump
" 12V electric fuel pump. Connects in series with the original fuel line. Keeps the hand pump. Avoids having to lift the hood to turn up gasoline before starting. To be powered through a push button for occasional operation. Low pressure, no need ...
€66.00 TTC
(55,00 € HT)
(55,00 € HT)
Standard 6V coil ignition
Branded ignition coil guaranteed for use with 6 V platinum-plated igniter (breakers). Impedance respected to prevent the breakers from becoming blue. Also works perfectly with electronic module or integral electronic igniter.
€43.20 TTC
(36,00 € HT)
(36,00 € HT)
Head gasket 2 mm solid copper Ford Vedette
Solid copper cylinder head gasket. 2mm thickness. Used with planed cylinder head. Tightening to 5m.kg. Mandatory installation with aerosol sealant, available here a>. Measured cylinder head thickness Head gasket type 37.3 mm ...
€160.40 TTC
(160,40 € HT)
(160,40 € HT)
Bearing 6203 - 17x40x12
Bearing - 17x40x12 waterproof (often used on dynamo, water pump, flywheel center, etc.). Check with the dimensions of your bearing.
€10.80 TTC
(9,00 € HT)
(9,00 € HT)
