Rod bearings Ford Vedette 53-54 or Simca Chambord - 040 - 43.57 mm
" Set of bearings (16 half-shells) for Ford Vedette 2nd generation 1953-54 and Simca V8 engines. Dimension: .040 US (1 mm) Each connecting rod receives its pair of bearings. "
€741.60 TTC
(618,00 € HT)
(618,00 € HT)
Ford Vedette air filter + breather sticker
" Sticker for air filter and breather cap. Mounts on Ford V8 Vedette, Vendôme, Cometer, Monte Carlo etc. Sticker "
€12.60 TTC
(10,50 € HT)
(10,50 € HT)
Oil filter foot gasket Ford Vedette Simca
Gasket to be placed between the central crankcase and the base of the oil filter. "Y" shaped.
€16.40 TTC
(16,40 € HT)
(16,40 € HT)
Reinforced collar for exhaust - Ø 52-55 mm
Reinforced collar for exhaust - Ø 52.55 mmRobust French manufacturing
€6.50 TTC
(5,42 € HT)
(5,42 € HT)
Rod bearings Ford Vedette 53-54 or Simca Chambord - 010 - 44.34 mm
" Set of bearings (16 half-shells) for Ford Vedette 2nd generation 1953-54 and Simca V8 engines. Dimension: .010 US (0.25 mm) Each connecting rod receives its pair of bearings. "
€504.00 TTC
(420,00 € HT)
(420,00 € HT)
Head gasket 2 mm solid copper Ford Vedette
Solid copper cylinder head gasket. 2mm thickness. Used with planed cylinder head. Tightening to 5m.kg. Mandatory installation with aerosol sealant, available here a>. Measured cylinder head thickness Head gasket type 37.3 mm ...
€160.40 TTC
(160,40 € HT)
(160,40 € HT)
Aerosol gasket for cylinder head
Sealing spray varnish to be sprayed on both sides of a cylinder head gasket. Improves sealing, essential with solid copper gaskets (any thickness)
€42.00 TTC
(35,00 € HT)
(35,00 € HT)
Head gasket 1.6 mm Ford Vedette standard
" Cylinder head gasket for Ford Vedette 1949 to 1954. One side all copper, the other with copper hems, thickness 1.6 mm approximately Measured cylinder head thickness Head gasket type 37.3 mm (original) 1.6 mm standard gasket from 37.0 ...
€90.00 TTC
(75,00 € HT)
(75,00 € HT)
Reinforced collar for exhaust - Ø 44-47 mm
Reinforced collar for exhaust - Ø 44-47 mmRobust French manufacturing
€5.80 TTC
(4,83 € HT)
(4,83 € HT)
Battery switch - safety
Battery isolator - used to electrically isolate the battery. To be placed on a terminal of the battery.
€12.00 TTC
(10,00 € HT)
(10,00 € HT)
Clutch mechanism Ford Vedette
Clutch mechanism reconditioned, in standard exchange mounted on Ford Vedette, Abeille, Comète, Monte Carlo, Vendôme engine Complete disassembly, micro balling, surfacing and retaring of the pressure plate. (The sending is done after receipt ...
€354.00 TTC
(295,00 € HT)
(295,00 € HT)
Pellet set of 4 - Ford Vedette and Simca engine block
Set of 4 pellets for Vedette Ford and Simca engine block diam. about 44 mm.
€44.00 TTC
(44,00 € HT)
(44,00 € HT)
Echappement joint extremite bloc V8 Ford Vedette et Simca
" Exhaust gasket, engine block outlet, small model placed at the ends. 4 on one engine - Sold individually. "
€7.20 TTC
(6,00 € HT)
(6,00 € HT)
Ford Vedette bearings - 030 - 52.54 mm
" Bearing set for Ford Vedette engine 1949 -54. (1 rear flange bearing + 2 front and central single bearings) Dimension: .030 US (0.75 mm) "
€810.00 TTC
(675,00 € HT)
(675,00 € HT)
Ford Vedette and Simca Versailles Chambord braid set
" Set of braids for crankshaft Vedette Ford and Simca Aquilon engine (rear bearing and front bearing) Versailles, Chambord etc ... New product, of very high technical quality. Mounts with ease, cuts easily with a cuter leaving 1 to 2 mm ...
€49.90 TTC
(41,58 € HT)
(41,58 € HT)
Ignition breakers RB (short) Ford Vedette Simca Versailles
A set of breakers for RB Ducellier igniter. Attention there are several RB versions - Please check your model according to the image. (Double igniters games require you to order 2 games.)
€42.60 TTC
(35,50 € HT)
(35,50 € HT)
