Rod bearings Ford Vedette 53-54 or Simca Chambord - 040 - 43.57 mm

" Set of bearings (16 half-shells) for Ford Vedette 2nd generation 1953-54 and Simca V8 engines. Dimension: .040 US (1 mm) Each connecting rod receives its pair of bearings. "

Oil seal rings gearbox lever - Simca Versailles Chambord

Set of 2 sealing rings (oil seal) for gearbox controls (mounted on control cover).Gaskets to be glued to immobilize them.

Water pump repair kit with aluminum impeller - Ford Vedette

Repair kit for water pump for "Y" or "T" pump body - years 1949-54. New axle is 16mm instead of 12 mm. So you need to drill body 16.5 mm. We recommend correcting the seat of the rotating joint at the back of the body.

Ignition set 8 spark plugs V8 Ford Vedette Simca Versailles Chambord

Set of 8 NGK spark plugs for Ford Vedette, Comète, Vendôme, Monte Carlo and Simca Trianon, Versailles, Régence, Beaulieu, Chambord, Présidence, Marly 1 and 2 engines. Thermal index adapted to fuel Lead Free 95 and 98.

Set of 8 pistons 67.00 Ford Vedette

Set of 8 pistons - New manufacture, similar to the original model - reduction in piston mass (approx. 255 gr with segments) - molybdenum treatment - cylinder dimension 67.00 mm. Supplied with segments, pins and circlips - The segments supplied ...

Head gasket 3 mm solid copper Ford Vedette

Solid copper cylinder head gasket. Thickness 3mm. Used with very planed cylinder head.Tightening at 5m.kg. Pose impérative avec le produit d'étanchéité en pâte pour les joint de culasse 2 ou 3 mm disponible ici.Cylinder head thickness measured ...

Electronic flasher unit 6V positive on ground - Ford Vedette

Ford Vedette disc clutch

Clutch disc reconditioned, in standard exchange for Ford Vedette. Complete disassembly, micro balling and painting. (The sending is done after receipt of the used mechanism, not destroyed)(Depending on the year, non-contractual photo)

€144.00 TTC
(120,00 € HT)

Aviation collex type paste gasket for cylinder head - 450ml

Sealing paste to be applied on both sides of a cylinder head gasket. Product similar to "Collex". Leave to evaporate for about 30 min at room temperature after application, then fit the gasket - improves the seal - recommended with solid copper ...

Fuel gauge - replacement float

Float in synthetic material resistant to current fuels. Used to replace the cork floats on the fuel gauge Length: 1.40" Diameter: 1.14"

Rod bearings Ford Vedette 53-54 or Simca Chambord - 020 - 44.08 mm

" Set of bearings (16 half-shells) for Ford Vedette 2nd generation 1953-54 and Simca V8 engines. Dimension: .020 US (0.50 mm) Each connecting rod receives its pair of bearings. "

Ignition coil 12v standard

Ignition coil guaranteed for use with a 12 V platinum screw igniter (breakers). Impedance respected to prevent the breakers from bluing.Works perfectly also with electronic module or integral electronic igniter. (Non contractual photo)

Clutch mechanism Ford Vedette

Clutch mechanism reconditioned, in standard exchange mounted on Ford Vedette, Abeille, Comète, Monte Carlo, Vendôme engine Complete disassembly, micro balling, surfacing and retaring of the pressure plate. (The sending is done after receipt ...

€315.00 TTC
(262,50 € HT)

Echappement sangle support renforcé 50 mm

Sangle de suspension pour échappement, caoutchouc armé. entraxe 52 mm pour vis M8 mm.

Central intake gasket - Ford Vedette

Central gasket intake housing for Vedette Ford. Special model for small Ford V8. Attention does not suit the V8 Simca Versailles -Chambord

rubber fuel gauge seal - 3-hole

Rubber seal for 3-hole fuel gauge