Regulateur électronique pour dynamo 6V positif à la masse - Ford Vedette - Simca Versailles

€208.00 TTC
(208,00 € HT)

Crankshaft bearing screws Ford 49 to 52

Set of bearing screws for V8 Ford Vedette model 1949 to 1952

Ignition coil 6V - High Performance

Bosch, NGK or Béru High Performance type ignition coil, guaranteed for use with:- 6 V platinum-plated screw igniter (breakers),- electronic ignition type 123 ignition,- platinum screw igniter + electronic amplification module

bearing stops - Ford 1953 to 54

Set of 4 retainers for V8 Ford Vedette 1949 - 52 (Strainer with spring and support on central bearing)

Electronic regulator for 6V negative ground dynamo

Electronic regulator for 6V negative ground dynamo - Original appearance in ED3 housing.For dynamos with positive excitation.Charge stabilization at 7.4V. Brighter lighting, better battery charge quality, improved ignition voltage.(Exchange standard)

€208.00 TTC
(208,00 € HT)

Rod bearings Ford Vedette 53-54 or Simca Chambord - 040 - 43.57 mm

" Set of bearings (16 half-shells) for Ford Vedette 2nd generation 1953-54 and Simca V8 engines. Dimension: .040 US (1 mm) Each connecting rod receives its pair of bearings. "

Set of 8 pistons 66.04 Ford Vedette

Set of 8 pistons - New manufacture, similar to the original model - reduction in piston mass (approximately 255 gr with rings) - molybdenum treatment - cylinder dimension 66.04 mm. Supplied with segments, pins and circlips - The segments supplied ...

Rod bearings Ford Vedette 53-54 or Simca Chambord - 010 - 44.34 mm

" Set of bearings (16 half-shells) for Ford Vedette 2nd generation 1953-54 and Simca V8 engines. Dimension: .010 US (0.25 mm) Each connecting rod receives its pair of bearings. "

Ignition coil 12v VALEO

Ignition coil guaranteed for use with a 12 V platinum screw igniter (breakers). Impedance respected to prevent the breakers from bluing.Works perfectly also with electronic module or integral electronic igniter. (Non contractual photo)

Pinion oil pump mounted on axis - Ford Vedette

Replacement gear for oil pump - V8 Ford Vedette.Delivered riveted with new axle. (Advantageously replaces the celoron one that has become fragile over time)Attention for the V8 Simca 13 hp 2350 cm3, choose the reference "Simca oil pump pinion" on ...

€270.20 TTC
(270,20 € HT)

Fuel gauge - replacement float

Float in synthetic material resistant to current fuels. Used to replace the cork floats on the fuel gauge Length: 1.40" Diameter: 1.14"

Exhaust - Y tube - 2 in 1 stainless steel - Ford Vedette

Stainless steel exhaust - Y connecting the 2 cast iron manifolds to line. Ford Vedette 1949 to 1954.

€436.40 TTC
(363,67 € HT)

Rod bearings Ford Vedette 53-54 or Simca Chambord - 030 - 43.83 mm

" Set of bearings (16 half-shells) for Ford Vedette 2nd generation 1953-54 and Simca V8 engines. Dimension: .030 US (0.75 mm) Each connecting rod receives its pair of bearings. "

Ford Vedette bearings - 030 - 52.54 mm

" Bearing set for Ford Vedette engine 1949 -54. (1 rear flange bearing + 2 front and central single bearings) Dimension: .030 US (0.75 mm) "

Reinforced collar for exhaust - Ø 52-55 mm

Reinforced collar for exhaust - Ø 52.55 mmRobust French manufacturing

Jeu de 8 pistons complets Ø à préciser à la commande - Ford comète