Exhaust - outlet tube + stainless steel stock - Ford Vedette
" Outlet tube with crosshead (bridge passage) to be connected to the silencer outlet. Ford Vedette 1949 to 1954. All stainless steel. "
(355,00 € HT)

Exhaust - stainless steel oval silencer - Ford Vedette
Stainless steel silencer for Ford Vedette.
(379,00 € HT)

copy of Exhaust - outlet tube + stainless steel stock - Ford Vendome - MONTE CARLO
" Outlet tube with bracket (passage of the bridge) to be connected to the outlet of the silencer. Ford Vendôme and Monte Carlo. All stainless steel. "
(24,95 € HT)

16 other products in the same category:
Ford Vedette V8 oil filter housing seal
Circular seal for Ford Vedette, Vendôme and Simca Vedette oil filter housing.Can be mounted on a cover or on a base depending on the model and year
(12,80 € HT)
Electronic regulator for 6V negative ground dynamo
Electronic regulator for 6V negative ground dynamo - Original appearance in ED3 housing.For dynamos with positive excitation.Charge stabilization at 7.4V. Brighter lighting, better battery charge quality, improved ignition voltage.(Exchange standard)
(208,00 € HT)

sticker ford oil filter
Oil filter sticker. Mounts on Ford V8 Vedette, Vendôme, Comète, Monte Carlo etc.
(6,00 € HT)
Oil pressure contact mano - Ford Vedette 1949 - 54
oil pressure switch for Ford Vedette engine from 1949 to 1954 - Thread M 10x100
(10,50 € HT)
Ford Vedette oil pump pinion
Replacement gear for oil pump - V8 Ford Vedette. Supplied with 4 rivets. (Advantageously replaces the celoron one that has become fragile over time)Attention for the V8 Simca 13 hp 2350 cm3, choose the reference "Simca oil pump pinion" on our shop.
(187,00 € HT)

Central intake gasket - Ford Vedette
Central gasket intake housing for Vedette Ford. Special model for small Ford V8. Attention does not suit the V8 Simca Versailles -Chambord
(50,00 € HT)
Fuel gauge - replacement plastic float
White plastic float. Used to replace ring gauge floats.
(12,50 € HT)
Ford Vedette COTAL disc clutch 215 mm
Clutch disc reconditioned, (exchange) - fit to Ford Vedette. Complete disassembly, micro balling and painting. (The sending is done after receipt of the used mechanism, not destroyed)(Depending on the year, non-contractual photo)
(120,00 € HT)

bearing stops - Ford 1953 to 54
Set of 4 retainers for V8 Ford Vedette 1949 - 52 (Strainer with spring and support on central bearing)
(20,52 € HT)
Fuel gauge - replacement float
Float in synthetic material resistant to current fuels. Used to replace the cork floats on the fuel gauge Length: 1.40" Diameter: 1.14"
(17,72 € HT)
Kit of 12V electric fuel pump
" 12V electric fuel pump. Connects in series with the original fuel line. Keeps the hand pump. Avoids having to lift the hood to turn up gasoline before starting. To be powered through a push button for occasional operation. Low pressure, no need ...
(80,00 € HT)
Ford Vedette exhaust valve
Ford Vedette exhaust valve, flared tail, rectified used.
(66,40 € HT)
IGOL 20W50 mineral oil - 5L can
5 l can (non contractual photo) - Viscosity: 20W-50BenefitsHéRITAGE GTZ mineral oil.Multigrade lubricant for Gasoline and Diesel engines, made from severely refined mineral bases and additives suitable for older engines. The anti-wear additive ...
(30,00 € HT)
Ford Vedette and Simca Versailles Chambord braid set
" Set of braids for crankshaft Vedette Ford and Simca Aquilon engine (rear bearing and front bearing) Versailles, Chambord etc ... New product, of very high technical quality. Mounts with ease, cuts easily with a cuter leaving 1 to 2 mm ...
(41,58 € HT)
Accelerator pump kit for Stromberg 22.2 Ford Vedette carburettor
Accelerator pump kit for Stromberg 22.2 carburettor. Fitting on Ford Vedette.
(44,00 € HT)
Viewed products
Central intake gasket Ford Vedette Simca
Central gasket intake housing for Vedette Ford and Simca.
(50,00 € HT)
Gearbox entry seal ring - Simca Versailles Chambord
Sealing ring (oil seal) for gearbox inlet (clutch side).
(12,00 € HT)