Ford Vedette bearings - 020 - 52.79 mm

" Bearing set for Ford Vedette engine 1949 -54. (1 rear flange bearing + 2 front and central single bearings) Dimension: .020 US (0.50 mm) "

Clutch mechanism Ford Vedette

Clutch mechanism reconditioned, in standard exchange mounted on Ford Vedette, Abeille, Comète, Monte Carlo, Vendôme engine Complete disassembly, micro balling, surfacing and retaring of the pressure plate. (The sending is done after receipt ...

€354.00 TTC
(295,00 € HT)

Ford Vedette 54 disc clutch 215 mm

Clutch disc reconditioned, in standard exchange for Ford Vedette. Complete disassembly, micro balling and painting. (The sending is done after receipt of the used mechanism, not destroyed)(Depending on the year, non-contractual photo)

€144.00 TTC
(120,00 € HT)

Oil filter foot gasket Ford Vedette Simca

Gasket to be placed between the central crankcase and the base of the oil filter. "Y" shaped.

fuel filter Big size ø 6 and 8 mm

Paper fuel filter for 6 or 8 mm hose.

Rod bearings Ford Vedette 53-54 or Simca Chambord - 010 - 44.34 mm

" Set of bearings (16 half-shells) for Ford Vedette 2nd generation 1953-54 and Simca V8 engines. Dimension: .010 US (0.25 mm) Each connecting rod receives its pair of bearings. "

rubber fuel gauge seal - 3-hole

Rubber seal for 3-hole fuel gauge

Oil pressure contact mano - Ford Vedette 1949 - 54

oil pressure switch for Ford Vedette engine from 1949 to 1954 - Thread M 10x100

Ford Vedette dynamo-fan belt

Secondary propeller-dynamo belt for Ford Vedette

Ford Vedette and Simca Versailles Chambord braid set

" Set of braids for crankshaft Vedette Ford and Simca Aquilon engine (rear bearing and front bearing) Versailles, Chambord etc ... New product, of very high technical quality. Mounts with ease, cuts easily with a cuter leaving 1 to 2 mm ...

Ford Vedette cylinder head bolt set

Set of 34 hexagon head screws to replace the original studs - 3/8 16f / p unc 2 lengths of screws in the set - Allows easy removal of cylinder heads. Tightening 5 m.kg maximum

Engine paint oxide green RAL 6020 - 500 ml

Engine paint oxide green RAL 6020 -Pot of 500 mlSuitable for engines, housings, gearboxes, differentials, brake drums and all parts subject to heating in cast iron, steel and light alloys.Direct application on degreased metal (or better, treated ...

€40.80 TTC
(34,00 € HT)

Water pump repair kit with aluminum impeller - Ford Vedette

Repair kit for water pump for "Y" or "T" pump body - years 1949-54. New axle is 16mm instead of 12 mm. So you need to drill body 16.5 mm. We recommend correcting the seat of the rotating joint at the back of the body.

Jeu de 8 pistons complets Ø à préciser à la commande - Ford comète

Ford Vedette gear lever retaining or repair ring -

This part fits around the gearshift lever. Its purpose is to protect the bowl that receives the lever base from breakage. Over time, the metal (Zamac) weakens and breaks. This ring also serves to repair the bowl when it begins to break.

€56.00 TTC
(56,00 € HT)

Calibrouge (Plastigage) mechanical clearance measurement

"Plastigage"The Calibrouge ("plastigage or plastigauge") is a simple and practical tool for measuring the clearances of your bearings. Range of use: operating clearance from 0.025 to 0.175 mm