Ford Vedette cylinder head bolt set
Set of 34 hexagon head screws to replace the original studs - 3/8 16f / p unc 2 lengths of screws in the set - Allows easy removal of cylinder heads. Tightening 5 m.kg maximum
€155.20 TTC
(155,20 € HT)
(155,20 € HT)
Exhaust - outlet tube + stainless steel stock - Ford Vedette
" Outlet tube with crosshead (bridge passage) to be connected to the silencer outlet. Ford Vedette 1949 to 1954. All stainless steel. "
€426.00 TTC
(355,00 € HT)
(355,00 € HT)
Reinforced collar for exhaust - Ø 44-47 mm
Reinforced collar for exhaust - Ø 44-47 mmRobust French manufacturing
€5.80 TTC
(4,83 € HT)
(4,83 € HT)
Set of 8 pistons 67.50 Ford Vedette
Set of 8 pistons - New manufacture, similar to the original model - reduction in piston mass (approximately 255 gr with rings) - molybdenum treatment - cylinder size 67.50 mm. Supplied with segments, pins and circlips - The segments supplied are ...
€1,548.00 TTC
(1 290,00 € HT)
(1 290,00 € HT)
Calibrouge (Plastigage) mechanical clearance measurement
"Plastigage"The Calibrouge ("plastigage or plastigauge") is a simple and practical tool for measuring the clearances of your bearings. Range of use: operating clearance from 0.025 to 0.175 mm
€27.00 TTC
(22,50 € HT)
(22,50 € HT)
Gasket paste for motor - auto extrudable cartridge 200 ml
Mot. Silicone gasket & self-extruding housing RTV K164 high-quality, heat-resistant silicone base: modified oxime silicone (acid-free hardening system)
€42.00 TTC
(35,00 € HT)
(35,00 € HT)
Water pump repair kit with aluminum impeller - Ford Vedette
Repair kit for water pump for "Y" or "T" pump body - years 1949-54. New axle is 16mm instead of 12 mm. So you need to drill body 16.5 mm. We recommend correcting the seat of the rotating joint at the back of the body.
€151.20 TTC
(151,20 € HT)
(151,20 € HT)
Exhaust - stainless steel oval silencer - Ford Vedette
Stainless steel silencer for Ford Vedette.
€454.80 TTC
(379,00 € HT)
(379,00 € HT)
Ignition coil 12v VALEO
Ignition coil guaranteed for use with a 12 V platinum screw igniter (breakers). Impedance respected to prevent the breakers from bluing.Works perfectly also with electronic module or integral electronic igniter. (Non contractual photo)
€60.00 TTC
(50,00 € HT)
(50,00 € HT)
Aviation collex type paste gasket for cylinder head - 117ml
Sealing paste to be applied on both sides of a cylinder head gasket. Product similar to "Collex". Leave to evaporate for about 30 min at room temperature after application, then fit the gasket - improves the seal - recommended with solid copper ...
€27.60 TTC
(23,00 € HT)
(23,00 € HT)
Fuel gauge - replacement float
Float in synthetic material resistant to current fuels. Used to replace the cork floats on the fuel gauge Length: 1.40" Diameter: 1.14"
€17.72 TTC
(17,72 € HT)
(17,72 € HT)
Kit of 12V electric fuel pump
" 12V electric fuel pump. Connects in series with the original fuel line. Keeps the hand pump. Avoids having to lift the hood to turn up gasoline before starting. To be powered through a push button for occasional operation. Low pressure, no need ...
€96.00 TTC
(80,00 € HT)
(80,00 € HT)
Accelerator pump kit for Stromberg 22.2 Ford Vedette carburettor
Accelerator pump kit for Stromberg 22.2 carburettor. Fitting on Ford Vedette.
€36.00 TTC
(30,00 € HT)
(30,00 € HT)
Manometer Tachometer - 2 - 4 - 6 - 8 cyl - electric 12V - black background - for negative to mass
Mano "OS" Tachometer 0 to 5000 rpm for 4-cylinder petrol engine. Connects to the "break" terminal on the ignition coil. 52 mm recess on the pressure gauge side. delivered with lighting. for negative to ground
€69.95 TTC
(58,29 € HT)
(58,29 € HT)
