Exhaust - outlet tube + stainless steel stock - Ford Vendome - MONTE CARLO
" Outlet tube with bracket (passage of the bridge) to be connected to the outlet of the silencer. Ford Vendôme and Monte Carlo. All stainless steel. "
(326,00 € HT)

Exhaust - Y tube - 2 in 1 stainless steel - Ford Vendome - MONTE CARLO
Stainless steel exhaust - Y connecting the 2 cast iron manifolds to line. Ford Vendôme and Monte Carlo.
(364,00 € HT)

Exhaust - round stainless steel silencer - Ford Vendome - MONTE CARLO
Stainless steel silencer for Ford Vendôme and Monté Carlo. French manufacture.
(478,00 € HT)

16 other products in the same category:
Exhaust suspension ring 63x96 width 27 mm - Peugeot 203
Suspension ring for Peugeot 203 exhaust and othersDimension approximately 63 x 96 x width 27 mm
(11,00 € HT)
IGOL semi-synthetic 15W50 oil - 5L can
Can of 5 L.Viscosity: 15W-50BenefitsHéRITAGE ZS semi-synthetic oil.Multigrade lubricant for gasoline engine of tourism, reinforced with synthetic bases, particularly adapted to the old engines, gasoline or diesel, equipped with an oil filter - ...
(35,00 € HT)
Ford Vedette V8 oil filter housing seal
Circular seal for Ford Vedette, Vendôme and Simca Vedette oil filter housing.Can be mounted on a cover or on a base depending on the model and year
(8,96 € HT)
Engine paint black RAL 9005 - 500 ml
Black paint - 500 ml jarSuitable for engines, housings, gearboxes, differentials, brake drums and all parts subject to heating in cast iron, steel and light alloys.Direct application on degreased metal (or better, treated with our Phosprim 4090), ...
(34,00 € HT)

Fuel pump - GUIOT diaphragm kit Ø90mm - Ford Vedette Simca
Replacement diaphragm for GUIOT fuel pump (Vedette Ford and Simca engine). Diam 90mm. Supplied with membrane and gaskets. (check the type of pump before ordering)
(25,00 € HT)
Battery switch - safety
Battery isolator - used to electrically isolate the battery. To be placed on a terminal of the battery.
(10,00 € HT)
160 mm float fuel gauge - 6V
" Float fuel gauge. Adaptable model. Arm length approx. 160 mm. External diameter of plate 54 mm - fixing center distance 38 mm. Supplied with cork seal. 3-hole fixing. Internal resistance approx. 110 ohms. For 6-volt vehicle only. "
(40,00 € HT)
Calibrouge (Plastigage) mechanical clearance measurement
"Plastigage"The Calibrouge ("plastigage or plastigauge") is a simple and practical tool for measuring the clearances of your bearings. Range of use: operating clearance from 0.025 to 0.175 mm
(22,50 € HT)
Electric Easy Drive power steering kit
(1 690,00 € HT)
Standard 6V coil ignition
Branded ignition coil guaranteed for use with 6 V platinum-plated igniter (breakers). Impedance respected to prevent the breakers from becoming blue. Also works perfectly with electronic module or integral electronic igniter.
(43,00 € HT)
Aviation collex type paste gasket for cylinder head - 117ml
Sealing paste to be applied on both sides of a cylinder head gasket. Product similar to "Collex". Leave to evaporate for about 30 min at room temperature after application, then fit the gasket - improves the seal - recommended with solid copper ...
(25,00 € HT)
Engine paint oxide green RAL 6020 - 500 ml
Engine paint oxide green RAL 6020 -Pot of 500 mlSuitable for engines, housings, gearboxes, differentials, brake drums and all parts subject to heating in cast iron, steel and light alloys.Direct application on degreased metal (or better, treated ...
(34,00 € HT)

sticker ford oil filter
Oil filter sticker. Mounts on Ford V8 Vedette, Vendôme, Comète, Monte Carlo etc.
(9,63 € HT)