
Fuel pump - 6V or 12V control push button
6 or 12v 10A push button. Can be used to activate an electric fuel pump for a few seconds, for example.
(8,25 € HT)
copy of Valves x 4 - ADM Ø 37x9x109 - plate - Citroen Traction 11D
Set of 4 ADM valves Ø 37x9x109 - flat - Citroen Traction 11D
(132,00 € HT)
Connecting rod bearings (set) 47.50 mm dimension 0.50 - Citroen Traction 11D - HY -U23
Set of 47.50 mm connecting rod bearings - dimension 0.50 mm - Citroen Traction 11D - HY - U23Mounts on engines equipped with bearing connecting rods.
(85,00 € HT)
Ignition coil 12v VALEO
Ignition coil guaranteed for use with a 12 V platinum screw igniter (breakers). Impedance respected to prevent the breakers from bluing.Works perfectly also with electronic module or integral electronic igniter. (Non contractual photo)
(48,00 € HT)
Carburetor similar to the Solex 32 PBIC Traction Citroen type
New carburettor similar to the Solex 32 PBIC type. Vacuum outlet on foot base. Configuration for Citroen TractionNozzle 26 - Main jet 135 and automatic nozzle 190 - Emulsion19 - Idle 50 - idle air 130 - Needle 1.5 - Float 12.5 gr - Accelerator ...
(163,07 € HT)
Calibrouge (Plastigage) mechanical clearance measurement
"Plastigage"The Calibrouge ("plastigage or plastigauge") is a simple and practical tool for measuring the clearances of your bearings. Range of use: operating clearance from 0.025 to 0.175 mm
(22,50 € HT)
Bearings 54.00mm - STD dimension - without cheek - Citroen HY
Bearing bearings dimension 50.00 (STD) -For ID 19 engine and similar engine block
(148,00 € HT)
12v to 6v regulator for temperature, pressure, fuel gauge
This module allows the use of 6V pressure gauges on a 12V vehicle (negative to ground). Mounts on a temperature gauge, pressure, fuel gauge, ...Very practical, it is fixed directly on the supply terminal of the pressure gauge thanks to a hole ...
(30,00 € HT)
gasket for solex 32 pbic carburetor
2 x paper gaskets for Solex 32 pbi carburetor base.Fixing center distance: 60 mmCentral passage: 32 mmTotal length: 78 mmwidth: 50mm
(3,80 € HT)
Axe 8 mm avec papillon pour réparation carburateur Solex 32 PBIC ou similaire
(22,00 € HT)
Citroen traction disc clutch
Clutch disc reconditioned, in standard exchange Traction, type H, HY, U23 and derivatives. Complete disassembly, micro balling and painting. (The sending is done after receipt of the used mechanism, not destroyed)(Depending on the year, ...
(115,00 € HT)

Clutch thrust ball bearing for 3-latch mechanism - Traction Citroen
Bearing for clutch release associated with the 3-latch mechanism and heavy plate.(Depending on year, non-contractual photo)
(75,00 € HT)

Aviation collex type paste gasket for cylinder head - 450ml
Sealing paste to be applied on both sides of a cylinder head gasket. Product similar to "Collex". Leave to evaporate for about 30 min at room temperature after application, then fit the gasket - improves the seal - recommended with solid copper ...
(35,00 € HT)
Carburateur similaire au type Solex 34 PBIC Traction Citroen et ID 19
Carburateur neuf type Solex 34 PBIC. Prise de dépression sur embase de pied. Configuration pour Citroen Traction - ID 19 Buse 27 - Gicleur principal 140 et ajutage automaticité 165 - Emulsion19 - Ralenti 50 - air ralenti 130 - Pointeau 1.5 - ...
(165,00 € HT)
Bearing bearings dimension 49.25 mm (0.75) - Citroen Traction HY U23
Bearing bearings dimension 49.25 (0.75) -Citroen: a- Traction Perfo and 11D - HY until 1963 ("Traction" type engine)- U23
(398,00 € HT)