Set of 13 cylinder head bolts 10x102x24 Perfo engine - Citroen Traction U23 HY

Set of 13 cylinder head screws 10x102x24 Perfo engine - Citroen Traction U23 HY

fuel filter ø 6 and 8 mm

Paper fuel filter for 6 or 8 mm hose.

12v to 6v regulator for temperature, pressure, fuel gauge

This module allows the use of 6V pressure gauges on a 12V vehicle (negative to ground). Mounts on a temperature gauge, pressure, fuel gauge, ...Very practical, it is fixed directly on the supply terminal of the pressure gauge thanks to a hole ...

Set of 3 25mm pellets for cast iron cylinder head - Citroen Traction U23 HY

Set of 3 Ø25mm pellets only for cast iron cylinder head - Citroen Traction U23 HY

Disc clutch kit + mechanism + thrust bearing in standard exchange Citroen Traction 15CV

Disc clutch kit + mechanism + thrust bearing in standard exchange Citroen Traction 15CV

€768.00 TTC
(640,00 € HT)

Fuel pump - GUIOT 90 mm diaphragm kit Citroen Traction U23 HY

Replacement diaphragm for GUIOT fuel pump (Citroen Traction U23 HY engine). Ø 90mm. Supplied with membrane and gaskets. (check the type of pump before ordering)

Valve guide Ø 9 X 13.06 X 55 - CITROeN Traction 11 - HY - U23

Valve guide Ø 9 X 13.06 X 55 - CITROËN Traction 11 - HY - U23 -Cast iron material

Connecting rod bearings (set) 47.00 mm dimension 1.00 - Citroen Traction 11D - HY -U23

Conrod bearing set 47.00 mm - dimension 1.00 mm - Citroen Traction 11D - HY - U23Mounts on engines equipped with bearing connecting rods.

Axe 8 mm avec papillon pour réparation carburateur Solex 32 PBIC ou similaire

Valves x 4 - ADM Ø 37x9x101.6 - Citroen Traction 11 perfo - HY Perfo engine - U23 flat wings

Set of 4 ADM valves Ø 37x9x101.6 - Citroen Traction 11 perfo - HY from 1955 to 63 Perfo engine - U23 flat wings

Bearings 54.00mm - STD dimension - without cheek - Citroen HY

Bearing bearings dimension 50.00 (STD) -For ID 19 engine and similar engine block

Ignition set of SEV breakers

" Set of breakers for SEV igniter For Renault Prairie, R2087, Goélette and derivatives "

Calibrouge (Plastigage) mechanical clearance measurement

"Plastigage"The Calibrouge ("plastigage or plastigauge") is a simple and practical tool for measuring the clearances of your bearings. Range of use: operating clearance from 0.025 to 0.175 mm

Ignition head Ducellier 65 mm

Head for Ducellier distributor: Interlocking inside the head = 65 mm, outside about 72 mm.To be assembled with breakers 1 237 013 808, and ducellier finger.

Fuel gauge with float 6V - Traction

" 6 volt float fuel gauge for Traction. "

Ignition coil 12v VALEO

Ignition coil guaranteed for use with a 12 V platinum screw igniter (breakers). Impedance respected to prevent the breakers from bluing.Works perfectly also with electronic module or integral electronic igniter. (Non contractual photo)