Oil pressure contact mano - Ford Vedette 1949 - 54
oil pressure switch for Ford Vedette engine from 1949 to 1954 - Thread M 10x100
€12.60 TTC
(10,50 € HT)
(10,50 € HT)
Fuel gauge - replacement float
Float in synthetic material resistant to current fuels. Used to replace the cork floats on the fuel gauge Length: 1.40" Diameter: 1.14"
€17.72 TTC
(17,72 € HT)
(17,72 € HT)
Ford and Simca Vedette rod stopper
Set of 16 retainers for V8 Simca or Ford Vedette connecting rod. V8 12 and 13cvOriginally compliant
€34.30 TTC
(34,30 € HT)
(34,30 € HT)
Reinforced collar for exhaust - Ø 52-55 mm
Reinforced collar for exhaust - Ø 52.55 mmRobust French manufacturing
€6.50 TTC
(5,42 € HT)
(5,42 € HT)
Central intake gasket - Ford Vedette
Central gasket intake housing for Vedette Ford. Special model for small Ford V8. Attention does not suit the V8 Simca Versailles -Chambord
€60.00 TTC
(50,00 € HT)
(50,00 € HT)
Ford Vedette Stromberg 22.2 Carburetor Kit
Overhaul kit for Stromberg 22.2 (2x30 mm) carburetor. Delivered with complete recovery pump. Fitting on Ford Vedette.
€97.92 TTC
(81,60 € HT)
(81,60 € HT)
Bearing 6203 - 17x40x12
Bearing - 17x40x12 waterproof (often used on dynamo, water pump, flywheel center, etc.). Check with the dimensions of your bearing.
€10.80 TTC
(9,00 € HT)
(9,00 € HT)
Head gasket 2 mm solid copper Ford Vedette
Solid copper cylinder head gasket. 2mm thickness. Used with planed cylinder head. Tightening to 5m.kg. Mandatory installation with aerosol sealant, available here a>. Measured cylinder head thickness Head gasket type 37.3 mm ...
€160.40 TTC
(160,40 € HT)
(160,40 € HT)
Pellet set of 4 - Ford Vedette and Simca engine block
Set of 4 pellets for Vedette Ford and Simca engine block diam. about 44 mm.
€44.00 TTC
(44,00 € HT)
(44,00 € HT)
Exhaust - stainless steel oval silencer - Ford Vedette
Stainless steel silencer for Ford Vedette.
€454.80 TTC
(379,00 € HT)
(379,00 € HT)
Head gasket 3 mm solid copper Ford Vedette
Solid copper cylinder head gasket. Thickness 3mm. Used with very planed cylinder head.Tightening at 5m.kg. Pose impérative avec le produit d'étanchéité en pâte pour les joint de culasse 2 ou 3 mm disponible ici.Cylinder head thickness measured ...
€192.40 TTC
(192,40 € HT)
(192,40 € HT)
Ford Vedette gear lever retaining or repair ring -
This part fits around the gearshift lever. Its purpose is to protect the bowl that receives the lever base from breakage. Over time, the metal (Zamac) weakens and breaks. This ring also serves to repair the bowl when it begins to break.
€56.00 TTC
(56,00 € HT)
(56,00 € HT)
12V electric fuel pump
" 12V electric fuel pump. Connects in series with the original fuel line. Keeps the hand pump. Avoids having to lift the hood to turn up gasoline before starting. To be powered through a push button for occasional operation. Low pressure, no need ...
€36.00 TTC
(30,00 € HT)
(30,00 € HT)
Fuel pump - 6V or 12V control push button
6 or 12v 10A push button. Can be used to activate an electric fuel pump for a few seconds, for example.
€9.90 TTC
(8,25 € HT)
(8,25 € HT)
Set of 8 pistons 67.50 Ford Vedette
Set of 8 pistons - New manufacture, similar to the original model - reduction in piston mass (approximately 255 gr with rings) - molybdenum treatment - cylinder size 67.50 mm. Supplied with segments, pins and circlips - The segments supplied are ...
€1,548.00 TTC
(1 290,00 € HT)
(1 290,00 € HT)
Crankshaft bearing screws Ford 49 to 52
Set of bearing screws for V8 Ford Vedette model 1949 to 1952
€134.42 TTC
(134,42 € HT)
(134,42 € HT)
