
Reinforced collar for exhaust - Ø 64-67 mm
Reinforced collar for exhaust - Ø 64-67 mmRobust French manufacturing
(6,50 € HT)
Segment set Ø 67.50 mm Simca Chambord 2.38 x 2.38 x 5 - 8cyl
Jeu pour 8 Cylindre(s) Ø 67,2 1 (jeu à la coupe à ajuster pour chaque segment) 16 x 67,3 x 2,38 x 2,9 C1 8 x 67,5 x 5 x 2,6 XO21P
(167,00 € HT)
Simca Versailles Chambord oil pump pinion
Replacement pinion for oil pump - V8 Simca (Versaille, Chambord, etc.). Supplied with 4 rivets. (Advantageously replaces the celoron one which has become fragile over time). Attention for Ford Vedette 12hp 2150 cm3 V8s, choose the reference " ...
(187,00 € HT)

Ford Vedette Simca V8 Calorstat Thermostat
" Thermostat for cooling circuit. For V8 Vedette Ford and Simca Versailles, Chambord, Vendôme, Monte Carlo etc. (Two thermostats per V8 engine). Sold individually. "
(20,00 € HT)
Ring x 2 - gearbox lever or column foot - Simca Versailles Chambord
Set of 2 repair rings to replace the silent blocks of the gearbox levers or those at the bottom of the column - Simca Versailles Chambord.Requires 2 sets per vehicle
(32,00 € HT)
Pellets set of 4 - Simca V8 cylinder heads
" Set of 4 Simca Aquilon type cylinder head pellets. diam 18.4 mm approximately (1 pellet per cylinder head) "
(28,00 € HT)
Spinnaker ring - the complete kit for Simca Versailles Chambord gearbox
Set of 4 rings for input, output and gearbox lever Simca Versailles Chambord
(30,62 € HT)
Electronic flasher unit 6V positive on ground - Simca Versailles
Electronic flasher unit 6V + to ground - Ford Vedette - Simca Versailles4 wires Simca Versailles 6 V (1 repeater on the dashboard)
(71,40 € HT)
Head gasket 1.6 mm Simca Versailles Chambord
" 1.6 mm cylinder head gasket for Simca V8 engine" "Aquilon" ". Measured cylinder head thickness Head gasket type 37.3 mm (original) 1.6 mm standard gasket from 37.0 to 37.3 mm 1.6 mm standard gasket from 36.0 to 36.9 ...
(66,50 € HT)
Fuel pump - GUIOT diaphragm kit Ø90mm - Ford Vedette Simca
Replacement diaphragm for GUIOT fuel pump (Vedette Ford and Simca engine). Diam 90mm. Supplied with membrane and gaskets. (check the type of pump before ordering)
(25,00 € HT)
Bearings for Simca Versailles Chambord standard - 53.30 mm
Set of bearings for Simca Versailles, Chambord, Ariane 8 etc. V8 "Aquilon" engine. (1 rear bearing + 2 front and central single bearings) Dimension: STD
(270,00 € HT)
Water plate gasket for Simca Versailles Chambord
Plate seal behind the timing cover
(8,30 € HT)
Aerosol gasket for cylinder head
Sealing spray varnish to be sprayed on both sides of a cylinder head gasket. Improves sealing, essential with solid copper gaskets (any thickness)
(35,00 € HT)
sticker Simca oil filter
Sticker for oil filter and breather plug. Mounts on V8 engine
(9,63 € HT)
Ignition harness V8 Ford Vedette Simca Versailles Chambord
High performance ignition harness, black silicone, interference suppression in accordance with European legislation. Lengths specially adapted for Ford Vedette, Bee V8 engines; Vendôme, Comète, Monte Carlo and Simca Trianon, Versailles, Régence, ...
(69,96 € HT)
copy of Segment set Ø 67.50 mm Simca Chambord 2 x 2 x 5 - 8cyl
Segment set Ø 67.50 mm Simca 2 x2 x 5 - 8cyl
(167,00 € HT)